Description
In the Linux kernel, the following vulnerability has been resolved:

can: bcm: add locking when updating filter and timer values

KCSAN detected a simultaneous access to timer values that can be
overwritten in bcm_rx_setup() when updating timer and filter content
while bcm_rx_handler(), bcm_rx_timeout_handler() or bcm_rx_thr_handler()
run concurrently on incoming CAN traffic.

Protect the timer (ival1/ival2/kt_ival1/kt_ival2/kt_lastmsg) and filter
(nframes/flags/frames/last_frames) updates in bcm_rx_setup() with a new
per-op bcm_rx_update_lock, taken with the matching scope in the RX
handlers. memcpy_from_msg() is staged into a temporary buffer before the
lock is taken, since it can sleep and must not run under a spinlock.

hrtimer_cancel() is always called without bcm_rx_update_lock held, since
bcm_rx_timeout_handler()/bcm_rx_thr_handler() take the same lock and a
running callback would otherwise deadlock against the canceller.

Also close a related race: bcm_rx_setup() cleared the RTR flag in the
stored reply frame's can_id as a separate, unprotected step after the
frame content was already installed, so a concurrent bcm_rx_handler()
could transmit a stale reply with CAN_RTR_FLAG still set. Fold that
normalization into the initial frame preparation instead (on the staged
buffer for updates, directly on op->frames pre-registration for new
ops), so the installed frame is always atomically self-consistent.

bcm_rx_handler()'s RX_RTR_FRAME check now takes a lock-protected
snapshot of op->flags before deciding whether to call bcm_can_tx(),
but does not hold the lock across that call.

Also take a lock-protected snapshot of the currframe in bcm_can_tx()
to avoid partly overwrites by content updates in bcm_tx_setup().
Finally check if a TX_RESET_MULTI_IDX/SETTIMER might have reset
op->currframe between the two locked sections in bcm_can_tx().

Omit calling hrtimer_forward() with zero interval in bcm_rx_thr_handler().
kt_ival2 may have been concurrently cleared by bcm_rx_setup() before it
cancels this timer, so check kt_ival2 inside the bcm_rx_update_lock.
Published: 2026-08-15
Score: n/a
EPSS: < 1% Very Low
KEV: No
Impact: n/a
Action: n/a
AI Analysis

Analysis and contextual insights are available on OpenCVE Cloud.

Remediation

No vendor fix or workaround currently provided.

Additional remediation guidance may be available on OpenCVE Cloud.

Tracking

Sign in to view the affected projects.

Advisories

No advisories yet.

History

Sat, 15 Aug 2026 21:30:00 +0000

Type Values Removed Values Added
Weaknesses CWE-362

Sat, 15 Aug 2026 06:00:00 +0000

Type Values Removed Values Added
Description In the Linux kernel, the following vulnerability has been resolved: can: bcm: add locking when updating filter and timer values KCSAN detected a simultaneous access to timer values that can be overwritten in bcm_rx_setup() when updating timer and filter content while bcm_rx_handler(), bcm_rx_timeout_handler() or bcm_rx_thr_handler() run concurrently on incoming CAN traffic. Protect the timer (ival1/ival2/kt_ival1/kt_ival2/kt_lastmsg) and filter (nframes/flags/frames/last_frames) updates in bcm_rx_setup() with a new per-op bcm_rx_update_lock, taken with the matching scope in the RX handlers. memcpy_from_msg() is staged into a temporary buffer before the lock is taken, since it can sleep and must not run under a spinlock. hrtimer_cancel() is always called without bcm_rx_update_lock held, since bcm_rx_timeout_handler()/bcm_rx_thr_handler() take the same lock and a running callback would otherwise deadlock against the canceller. Also close a related race: bcm_rx_setup() cleared the RTR flag in the stored reply frame's can_id as a separate, unprotected step after the frame content was already installed, so a concurrent bcm_rx_handler() could transmit a stale reply with CAN_RTR_FLAG still set. Fold that normalization into the initial frame preparation instead (on the staged buffer for updates, directly on op->frames pre-registration for new ops), so the installed frame is always atomically self-consistent. bcm_rx_handler()'s RX_RTR_FRAME check now takes a lock-protected snapshot of op->flags before deciding whether to call bcm_can_tx(), but does not hold the lock across that call. Also take a lock-protected snapshot of the currframe in bcm_can_tx() to avoid partly overwrites by content updates in bcm_tx_setup(). Finally check if a TX_RESET_MULTI_IDX/SETTIMER might have reset op->currframe between the two locked sections in bcm_can_tx(). Omit calling hrtimer_forward() with zero interval in bcm_rx_thr_handler(). kt_ival2 may have been concurrently cleared by bcm_rx_setup() before it cancels this timer, so check kt_ival2 inside the bcm_rx_update_lock.
Title can: bcm: add locking when updating filter and timer values
First Time appeared Linux
Linux linux Kernel
CPEs cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:*
Vendors & Products Linux
Linux linux Kernel
References

Subscriptions

Linux Linux Kernel
cve-icon MITRE

Status: PUBLISHED

Assigner: Linux

Published:

Updated: 2026-08-15T05:52:59.959Z

Reserved: 2026-08-09T03:40:39.907Z

Link: CVE-2026-72121

cve-icon Vulnrichment

No data.

cve-icon NVD

Status : Received

Published: 2026-08-15T06:21:26.650

Modified: 2026-08-15T06:21:26.650

Link: CVE-2026-72121

cve-icon Redhat

No data.

cve-icon OpenCVE Enrichment

Updated: 2026-08-15T21:15:03Z

Weaknesses