Search
Search Results (2 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-98530 | 1 Linux | 1 Linux Kernel | 2026-10-18 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: kprobes: Fix permanent hang when flushing the kprobe optimizer Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build: # cd /sys/kernel/tracing # echo 'p:myprobe vfs_read+9' >> kprobe_events # echo 1 > events/kprobes/myprobe/enable # # wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED] # echo 0 > /proc/sys/debug/kprobes-optimization INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246. wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way. Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first: sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way. Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once. | ||||
| CVE-2026-89930 | 1 Linux | 1 Linux Kernel | 2026-09-18 | 9.3 Critical |
| In the Linux kernel, the following vulnerability has been resolved: KVM: nVMX: Service local TLB flushes on failed nested VM-Enter KVM services local TLB flushes on "full" nested VM-Exits (through __nested_vmx_vmexit()), but not if a nested VM-Enter fails (e.g. due to failed VMCS checks in nested_vmx_enter_non_root_mode()). However, it is possible that KVM had queued TLB flushes that need to be performed, even if the nested VM-Enter was not successful. For example, if VPID is disabled for L2 (via nested_vmx_transition_tlb_flush(), or if via the MSR load lists, as the SDM says: If any MSR is being loaded in such a way that would architecturally require a TLB flush, the TLBs are updated so that, after VM entry, the logical processor will not use any translations that were cached before the transition. The SDM is unclear about when the TLB flush should occur, and whether or not a failed VM entry would flush the TLB, so it is safer to always do the TLB flush in this case. More concretely, KVM also updates the last VPID L1 used for L2 in nested_vmx_transition_tlb_flush() (i.e. last_vpid), even if the VM entry ultimately fails. With the current code, KVM could miss a TLB flush if L1 changes L2's VPID, then does a failed VM entry followed by a successful one, as the failed VM entry would update last_vpid but not actually flush the TLB. Servicing local TLB flushes on failed VM entries makes sure that the TLB is always flushed when last_vpid is updated. | ||||
Page 1 of 1.