| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm/ident_map: Use gbpages only where full GB page should be mapped.
When ident_pud_init() uses only GB pages to create identity maps, large
ranges of addresses not actually requested can be included in the resulting
table; a 4K request will map a full GB. This can include a lot of extra
address space past that requested, including areas marked reserved by the
BIOS. That allows processor speculation into reserved regions, that on UV
systems can cause system halts.
Only use GB pages when map creation requests include the full GB page of
space. Fall back to using smaller 2M pages when only portions of a GB page
are included in the request.
No attempt is made to coalesce mapping requests. If a request requires a
map entry at the 2M (pmd) level, subsequent mapping requests within the
same 1G region will also be at the pmd level, even if adjacent or
overlapping such requests could have been combined to map a full GB page.
Existing usage starts with larger regions and then adds smaller regions, so
this should not have any great consequence. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/stm: Avoid use-after-free issues with crtc and plane
ltdc_load() calls functions drm_crtc_init_with_planes(),
drm_universal_plane_init() and drm_encoder_init(). These functions
should not be called with parameters allocated with devm_kzalloc()
to avoid use-after-free issues [1].
Use allocations managed by the DRM framework.
Found by Linux Verification Center (linuxtesting.org).
[1]
https://lore.kernel.org/lkml/u366i76e3qhh3ra5oxrtngjtm2u5lterkekcz6y2jkndhuxzli@diujon4h7qwb/ |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: Set correct chandef when starting CAC
When starting CAC in a mode other than AP mode, it return a
"WARNING: CPU: 0 PID: 63 at cfg80211_chandef_dfs_usable+0x20/0xaf [cfg80211]"
caused by the chandef.chan being null at the end of CAC.
Solution: Ensure the channel definition is set for the different modes
when starting CAC to avoid getting a NULL 'chan' at the end of CAC.
Call Trace:
? show_regs.part.0+0x14/0x16
? __warn+0x67/0xc0
? cfg80211_chandef_dfs_usable+0x20/0xaf [cfg80211]
? report_bug+0xa7/0x130
? exc_overflow+0x30/0x30
? handle_bug+0x27/0x50
? exc_invalid_op+0x18/0x60
? handle_exception+0xf6/0xf6
? exc_overflow+0x30/0x30
? cfg80211_chandef_dfs_usable+0x20/0xaf [cfg80211]
? exc_overflow+0x30/0x30
? cfg80211_chandef_dfs_usable+0x20/0xaf [cfg80211]
? regulatory_propagate_dfs_state.cold+0x1b/0x4c [cfg80211]
? cfg80211_propagate_cac_done_wk+0x1a/0x30 [cfg80211]
? process_one_work+0x165/0x280
? worker_thread+0x120/0x3f0
? kthread+0xc2/0xf0
? process_one_work+0x280/0x280
? kthread_complete_and_exit+0x20/0x20
? ret_from_fork+0x19/0x24
[shorten subject, remove OCB, reorder cases to match previous list] |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: PAD: fix crash in exit_round_robin()
The kernel occasionally crashes in cpumask_clear_cpu(), which is called
within exit_round_robin(), because when executing clear_bit(nr, addr) with
nr set to 0xffffffff, the address calculation may cause misalignment within
the memory, leading to access to an invalid memory address.
----------
BUG: unable to handle kernel paging request at ffffffffe0740618
...
CPU: 3 PID: 2919323 Comm: acpi_pad/14 Kdump: loaded Tainted: G OE X --------- - - 4.18.0-425.19.2.el8_7.x86_64 #1
...
RIP: 0010:power_saving_thread+0x313/0x411 [acpi_pad]
Code: 89 cd 48 89 d3 eb d1 48 c7 c7 55 70 72 c0 e8 64 86 b0 e4 c6 05 0d a1 02 00 01 e9 bc fd ff ff 45 89 e4 42 8b 04 a5 20 82 72 c0 <f0> 48 0f b3 05 f4 9c 01 00 42 c7 04 a5 20 82 72 c0 ff ff ff ff 31
RSP: 0018:ff72a5d51fa77ec8 EFLAGS: 00010202
RAX: 00000000ffffffff RBX: ff462981e5d8cb80 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246
RBP: ff46297556959d80 R08: 0000000000000382 R09: ff46297c8d0f38d8
R10: 0000000000000000 R11: 0000000000000001 R12: 000000000000000e
R13: 0000000000000000 R14: ffffffffffffffff R15: 000000000000000e
FS: 0000000000000000(0000) GS:ff46297a800c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffe0740618 CR3: 0000007e20410004 CR4: 0000000000771ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
? acpi_pad_add+0x120/0x120 [acpi_pad]
kthread+0x10b/0x130
? set_kthread_struct+0x50/0x50
ret_from_fork+0x1f/0x40
...
CR2: ffffffffe0740618
crash> dis -lr ffffffffc0726923
...
/usr/src/debug/kernel-4.18.0-425.19.2.el8_7/linux-4.18.0-425.19.2.el8_7.x86_64/./include/linux/cpumask.h: 114
0xffffffffc0726918 <power_saving_thread+776>: mov %r12d,%r12d
/usr/src/debug/kernel-4.18.0-425.19.2.el8_7/linux-4.18.0-425.19.2.el8_7.x86_64/./include/linux/cpumask.h: 325
0xffffffffc072691b <power_saving_thread+779>: mov -0x3f8d7de0(,%r12,4),%eax
/usr/src/debug/kernel-4.18.0-425.19.2.el8_7/linux-4.18.0-425.19.2.el8_7.x86_64/./arch/x86/include/asm/bitops.h: 80
0xffffffffc0726923 <power_saving_thread+787>: lock btr %rax,0x19cf4(%rip) # 0xffffffffc0740620 <pad_busy_cpus_bits>
crash> px tsk_in_cpu[14]
$66 = 0xffffffff
crash> px 0xffffffffc072692c+0x19cf4
$99 = 0xffffffffc0740620
crash> sym 0xffffffffc0740620
ffffffffc0740620 (b) pad_busy_cpus_bits [acpi_pad]
crash> px pad_busy_cpus_bits[0]
$42 = 0xfffc0
----------
To fix this, ensure that tsk_in_cpu[tsk_index] != -1 before calling
cpumask_clear_cpu() in exit_round_robin(), just as it is done in
round_robin_cpu().
[ rjw: Subject edit, avoid updates to the same value ] |
| In the Linux kernel, the following vulnerability has been resolved:
x86/ioapic: Handle allocation failures gracefully
Breno observed panics when using failslab under certain conditions during
runtime:
can not alloc irq_pin_list (-1,0,20)
Kernel panic - not syncing: IO-APIC: failed to add irq-pin. Can not proceed
panic+0x4e9/0x590
mp_irqdomain_alloc+0x9ab/0xa80
irq_domain_alloc_irqs_locked+0x25d/0x8d0
__irq_domain_alloc_irqs+0x80/0x110
mp_map_pin_to_irq+0x645/0x890
acpi_register_gsi_ioapic+0xe6/0x150
hpet_open+0x313/0x480
That's a pointless panic which is a leftover of the historic IO/APIC code
which panic'ed during early boot when the interrupt allocation failed.
The only place which might justify panic is the PIT/HPET timer_check() code
which tries to figure out whether the timer interrupt is delivered through
the IO/APIC. But that code does not require to handle interrupt allocation
failures. If the interrupt cannot be allocated then timer delivery fails
and it either panics due to that or falls back to legacy mode.
Cure this by removing the panic wrapper around __add_pin_to_irq_node() and
making mp_irqdomain_alloc() aware of the failure condition and handle it as
any other failure in this function gracefully. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu-tasks: Fix access non-existent percpu rtpcp variable in rcu_tasks_need_gpcb()
For kernels built with CONFIG_FORCE_NR_CPUS=y, the nr_cpu_ids is
defined as NR_CPUS instead of the number of possible cpus, this
will cause the following system panic:
smpboot: Allowing 4 CPUs, 0 hotplug CPUs
...
setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:512 nr_node_ids:1
...
BUG: unable to handle page fault for address: ffffffff9911c8c8
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 15 Comm: rcu_tasks_trace Tainted: G W
6.6.21 #1 5dc7acf91a5e8e9ac9dcfc35bee0245691283ea6
RIP: 0010:rcu_tasks_need_gpcb+0x25d/0x2c0
RSP: 0018:ffffa371c00a3e60 EFLAGS: 00010082
CR2: ffffffff9911c8c8 CR3: 000000040fa20005 CR4: 00000000001706f0
Call Trace:
<TASK>
? __die+0x23/0x80
? page_fault_oops+0xa4/0x180
? exc_page_fault+0x152/0x180
? asm_exc_page_fault+0x26/0x40
? rcu_tasks_need_gpcb+0x25d/0x2c0
? __pfx_rcu_tasks_kthread+0x40/0x40
rcu_tasks_one_gp+0x69/0x180
rcu_tasks_kthread+0x94/0xc0
kthread+0xe8/0x140
? __pfx_kthread+0x40/0x40
ret_from_fork+0x34/0x80
? __pfx_kthread+0x40/0x40
ret_from_fork_asm+0x1b/0x80
</TASK>
Considering that there may be holes in the CPU numbers, use the
maximum possible cpu number, instead of nr_cpu_ids, for configuring
enqueue and dequeue limits.
[ neeraj.upadhyay: Fix htmldocs build error reported by Stephen Rothwell ] |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Validate hdwq pointers before dereferencing in reset/errata paths
When the HBA is undergoing a reset or is handling an errata event, NULL ptr
dereference crashes may occur in routines such as
lpfc_sli_flush_io_rings(), lpfc_dev_loss_tmo_callbk(), or
lpfc_abort_handler().
Add NULL ptr checks before dereferencing hdwq pointers that may have been
freed due to operations colliding with a reset or errata event handler. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix a NULL pointer dereference when failed to start a new trasacntion
[BUG]
Syzbot reported a NULL pointer dereference with the following crash:
FAULT_INJECTION: forcing a failure.
start_transaction+0x830/0x1670 fs/btrfs/transaction.c:676
prepare_to_relocate+0x31f/0x4c0 fs/btrfs/relocation.c:3642
relocate_block_group+0x169/0xd20 fs/btrfs/relocation.c:3678
...
BTRFS info (device loop0): balance: ended with status: -12
Oops: general protection fault, probably for non-canonical address 0xdffffc00000000cc: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000660-0x0000000000000667]
RIP: 0010:btrfs_update_reloc_root+0x362/0xa80 fs/btrfs/relocation.c:926
Call Trace:
<TASK>
commit_fs_roots+0x2ee/0x720 fs/btrfs/transaction.c:1496
btrfs_commit_transaction+0xfaf/0x3740 fs/btrfs/transaction.c:2430
del_balance_item fs/btrfs/volumes.c:3678 [inline]
reset_balance_state+0x25e/0x3c0 fs/btrfs/volumes.c:3742
btrfs_balance+0xead/0x10c0 fs/btrfs/volumes.c:4574
btrfs_ioctl_balance+0x493/0x7c0 fs/btrfs/ioctl.c:3673
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[CAUSE]
The allocation failure happens at the start_transaction() inside
prepare_to_relocate(), and during the error handling we call
unset_reloc_control(), which makes fs_info->balance_ctl to be NULL.
Then we continue the error path cleanup in btrfs_balance() by calling
reset_balance_state() which will call del_balance_item() to fully delete
the balance item in the root tree.
However during the small window between set_reloc_contrl() and
unset_reloc_control(), we can have a subvolume tree update and created a
reloc_root for that subvolume.
Then we go into the final btrfs_commit_transaction() of
del_balance_item(), and into btrfs_update_reloc_root() inside
commit_fs_roots().
That function checks if fs_info->reloc_ctl is in the merge_reloc_tree
stage, but since fs_info->reloc_ctl is NULL, it results a NULL pointer
dereference.
[FIX]
Just add extra check on fs_info->reloc_ctl inside
btrfs_update_reloc_root(), before checking
fs_info->reloc_ctl->merge_reloc_tree.
That DEAD_RELOC_TREE handling is to prevent further modification to the
reloc tree during merge stage, but since there is no reloc_ctl at all,
we do not need to bother that. |
| In the Linux kernel, the following vulnerability has been resolved:
efistub/tpm: Use ACPI reclaim memory for event log to avoid corruption
The TPM event log table is a Linux specific construct, where the data
produced by the GetEventLog() boot service is cached in memory, and
passed on to the OS using an EFI configuration table.
The use of EFI_LOADER_DATA here results in the region being left
unreserved in the E820 memory map constructed by the EFI stub, and this
is the memory description that is passed on to the incoming kernel by
kexec, which is therefore unaware that the region should be reserved.
Even though the utility of the TPM2 event log after a kexec is
questionable, any corruption might send the parsing code off into the
weeds and crash the kernel. So let's use EFI_ACPI_RECLAIM_MEMORY
instead, which is always treated as reserved by the E820 conversion
logic. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: pause TCM when the firmware is stopped
Not doing so will make us send a host command to the transport while the
firmware is not alive, which will trigger a WARNING.
bad state = 0
WARNING: CPU: 2 PID: 17434 at drivers/net/wireless/intel/iwlwifi/iwl-trans.c:115 iwl_trans_send_cmd+0x1cb/0x1e0 [iwlwifi]
RIP: 0010:iwl_trans_send_cmd+0x1cb/0x1e0 [iwlwifi]
Call Trace:
<TASK>
iwl_mvm_send_cmd+0x40/0xc0 [iwlmvm]
iwl_mvm_config_scan+0x198/0x260 [iwlmvm]
iwl_mvm_recalc_tcm+0x730/0x11d0 [iwlmvm]
iwl_mvm_tcm_work+0x1d/0x30 [iwlmvm]
process_one_work+0x29e/0x640
worker_thread+0x2df/0x690
? rescuer_thread+0x540/0x540
kthread+0x192/0x1e0
? set_kthread_struct+0x90/0x90
ret_from_fork+0x22/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: add bounds checking to ocfs2_xattr_find_entry()
Add a paranoia check to make sure it doesn't stray beyond valid memory
region containing ocfs2 xattr entries when scanning for a match. It will
prevent out-of-bound access in case of crafted images. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm80xx: Set phy->enable_completion only when we wait for it
pm8001_phy_control() populates the enable_completion pointer with a stack
address, sends a PHY_LINK_RESET / PHY_HARD_RESET, waits 300 ms, and
returns. The problem arises when a phy control response comes late. After
300 ms the pm8001_phy_control() function returns and the passed
enable_completion stack address is no longer valid. Late phy control
response invokes complete() on a dangling enable_completion pointer which
leads to a kernel crash. |
| In the Linux kernel, the following vulnerability has been resolved:
dma-debug: fix a possible deadlock on radix_lock
radix_lock() shouldn't be held while holding dma_hash_entry[idx].lock
otherwise, there's a possible deadlock scenario when
dma debug API is called holding rq_lock():
CPU0 CPU1 CPU2
dma_free_attrs()
check_unmap() add_dma_entry() __schedule() //out
(A) rq_lock()
get_hash_bucket()
(A) dma_entry_hash
check_sync()
(A) radix_lock() (W) dma_entry_hash
dma_entry_free()
(W) radix_lock()
// CPU2's one
(W) rq_lock()
CPU1 situation can happen when it extending radix tree and
it tries to wake up kswapd via wake_all_kswapd().
CPU2 situation can happen while perf_event_task_sched_out()
(i.e. dma sync operation is called while deleting perf_event using
etm and etr tmc which are Arm Coresight hwtracing driver backends).
To remove this possible situation, call dma_entry_free() after
put_hash_bucket() in check_unmap(). |
| In the Linux kernel, the following vulnerability has been resolved:
pinmux: Use sequential access to access desc->pinmux data
When two client of the same gpio call pinctrl_select_state() for the
same functionality, we are seeing NULL pointer issue while accessing
desc->mux_owner.
Let's say two processes A, B executing in pin_request() for the same pin
and process A updates the desc->mux_usecount but not yet updated the
desc->mux_owner while process B see the desc->mux_usecount which got
updated by A path and further executes strcmp and while accessing
desc->mux_owner it crashes with NULL pointer.
Serialize the access to mux related setting with a mutex lock.
cpu0 (process A) cpu1(process B)
pinctrl_select_state() { pinctrl_select_state() {
pin_request() { pin_request() {
...
....
} else {
desc->mux_usecount++;
desc->mux_usecount && strcmp(desc->mux_owner, owner)) {
if (desc->mux_usecount > 1)
return 0;
desc->mux_owner = owner;
} } |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: don't BUG_ON on ENOMEM from btrfs_lookup_extent_info() in walk_down_proc()
We handle errors here properly, ENOMEM isn't fatal, return the error. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: clean up our handling of refs == 0 in snapshot delete
In reada we BUG_ON(refs == 0), which could be unkind since we aren't
holding a lock on the extent leaf and thus could get a transient
incorrect answer. In walk_down_proc we also BUG_ON(refs == 0), which
could happen if we have extent tree corruption. Change that to return
-EUCLEAN. In do_walk_down() we catch this case and handle it correctly,
however we return -EIO, which -EUCLEAN is a more appropriate error code.
Finally in walk_up_proc we have the same BUG_ON(refs == 0), so convert
that to proper error handling. Also adjust the error message so we can
actually do something with the information. |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: cevt-r4k: Don't call get_c0_compare_int if timer irq is installed
This avoids warning:
[ 0.118053] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:283
Caused by get_c0_compare_int on secondary CPU.
We also skipped saving IRQ number to struct clock_event_device *cd as
it's never used by clockevent core, as per comments it's only meant
for "non CPU local devices". |
| In the Linux kernel, the following vulnerability has been resolved:
ELF: fix kernel.randomize_va_space double read
ELF loader uses "randomize_va_space" twice. It is sysctl and can change
at any moment, so 2 loads could see 2 different values in theory with
unpredictable consequences.
Issue exactly one load for consistent value across one exec. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: use IWL_FW_CHECK for link ID check
The lookup function iwl_mvm_rcu_fw_link_id_to_link_conf() is
normally called with input from the firmware, so it should use
IWL_FW_CHECK() instead of WARN_ON(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/bridge: tc358767: Check if fully initialized before signalling HPD event via IRQ
Make sure the connector is fully initialized before signalling any
HPD events via drm_kms_helper_hotplug_event(), otherwise this may
lead to NULL pointer dereference. |
