| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
spi: xilinx: use FIFO occupancy register to determine buffer size
The method the driver uses to determine the size of the FIFO has a
problem. What it currently does is this:
It stops the SPI hardware and writes to the TX FIFO register until TX
FIFO FULL asserts in the status register. But the hardware does not only
have the FIFO, it also has a shift register which can hold a byte. This
can be seen, when writing a byte to the FIFO (while the SPI hardware is
stopped,) the TX FIFO EMPTY is still empty. So, if we have a FIFO size
of 16 for example, the current method returns a 17.
This is a problem, at least when using the driver in irq mode. The same
size determined for the TX FIFO is also assumed for the RX FIFO. When a
SPI transaction wants to write the amount of the FIFO size or more
bytes, the following happens, for example with 16 bytes FIFO size:
The driver stops the SPI hardware and writes 17 bytes to the TX FIFO and
starts the SPI hardware and goes sleep.
The hardware then shifts out 17 bytes (FIFO + shift register) and
simultaneously reads bytes into the RX FIFO, but it only has 16 places,
so it looses one byte. Then TX FIFO empty asserts, wakes the driver
again, which has a fast path and reads 16 bytes from the RX FIFO, but
before reading the last 17th byte (which is lost) it does this:
sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
xilinx_spi_rx(xspi);
rx_words--;
}
It reads the status register and checks if the RX FIFO is not empty.
But it is empty in our case. So this check spins in a while loop
forever locking the driver.
This patch fixes the logic to determine the FIFO size. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/dma-iommu: Fix wrong scatterlist length assignment in P2PDMA path
In iommu_dma_map_sg(), when handling PCI P2PDMA cases, the DMA length
of the current scatterlist segment `s` is incorrectly assigned from the
head entry `sg->length` instead of the current entry `s->length`.
This typo causes all P2PDMA segments in the scatterlist to inherit the
length of the first segment, leading to corrupted DMA lengths for multi-
segment scatterlists.
Fix this by using `s->length` instead of `sg->length`. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: reject inverted service ranges from peer bindings
tipc_update_nametbl() inserts a binding advertised by a peer node using
the lower and upper service-range bounds taken directly from the wire,
without checking that lower <= upper. The local bind path validates the
ordering (tipc_uaddr_valid()), but the name-distribution path does not.
A binding with lower > upper is inserted at the far end of the
service-range rbtree (keyed on lower) where no lookup or withdrawal can
ever match it (service_range_foreach_match() requires sr->lower <= end).
The publication, its service_range node and the augmented rbtree entry
are then leaked for the lifetime of the namespace, and there is no
per-peer cap equivalent to TIPC_MAX_PUBL on locally created bindings.
Reject inverted ranges in the network path as well. A peer node can
otherwise leak unbounded binding-table memory by sending PUBLICATION
items with lower > upper. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: require net admin for TIPCv2 netlink mutators
TIPCv2 registers mutating generic-netlink operations without admin
permission flags. Generic netlink only checks CAP_NET_ADMIN when an
operation sets GENL_ADMIN_PERM or GENL_UNS_ADMIN_PERM, so a local
unprivileged process can currently change TIPC state through commands
such as TIPC_NL_NET_SET, TIPC_NL_KEY_SET, TIPC_NL_KEY_FLUSH, and
bearer enable/disable.
The legacy TIPC netlink API already checks netlink_net_capable(...,
CAP_NET_ADMIN) for administrative commands. Give the TIPCv2 mutators
the equivalent generic-netlink gate. Use GENL_UNS_ADMIN_PERM, which
maps to the same namespace-aware CAP_NET_ADMIN check that
netlink_net_capable() performs, so the behaviour matches the legacy
path and keeps working for CAP_NET_ADMIN holders in a non-initial user
namespace (containers).
A QEMU/KASAN repro run as uid/gid 65534 with zero effective
capabilities previously succeeded in changing the network id and node
identity, setting and flushing key material, and enabling/disabling a
UDP bearer. With this patch applied the same operations fail with
-EPERM. |
| In the Linux kernel, the following vulnerability has been resolved:
net: Stop leased rxq before uninstalling its memory provider
netif_rxq_cleanup_unlease() tears down the memory provider that was
installed on a physical RX queue through a netkit queue lease. It
currently revokes the provider's DMA mappings before stopping the
physical queue:
__netif_mp_uninstall_rxq(virt_rxq, p); /* DMA unmap */
__netif_mp_close_rxq(phys_rxq->dev, rxq_idx, p); /* queue stop */
This inverts the ordering used by the regular teardown paths (normal
device unregister and the io_uring zcrx close path), which stop the
queue before revoking the provider's mappings.
With the physical queue still live, its NAPI can keep consuming
net_iov entries from the page_pool alloc cache after the
__netif_mp_uninstall_rxq() has already cleared their dma_addr,
opening a window for the device to DMA to a stale or zero address.
Fix it by swapping the two calls so the queue is stopped (and its
NAPI quiesced) before the provider is uninstalled. No functional
regression was observed across repeated runs of the nk_qlease.py
HW selftest, which exercises the lease teardown path; this was
tested against fbnic QEMU emulation. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: topology: Check PCM and DAI name strings before use
Topology objects store several PCM and DAI names in fixed-size UAPI
arrays. Other topology parser paths validate these fields with bounded
strnlen() checks before using them as C strings, but the PCM and DAI
paths still pass some fixed-size arrays directly to strlen(),
devm_kstrdup(), DAI lookup, and diagnostic prints.
A malformed topology blob with a non-NUL-terminated PCM, DAI, or stream
capability name can therefore make the parser read past the end of the
fixed-size field.
Reject unterminated PCM and DAI name fields before consuming them as C
strings. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: fsl: fsl_audmix: Validate written enum values
fsl_audmix_put_mix_clk_src() and fsl_audmix_put_out_src()
convert the user-provided enum item with snd_soc_enum_item_to_val()
before checking whether the item is within the enum's item count.
The generic snd_soc_put_enum_double() helper performs that
validation, but these callbacks use the converted value first: the
clock-source path tests it with BIT(), and the output-source path
indexes the prms transition table with it.
Reject out-of-range enum items before converting them. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: hdac_hdmi: Validate written enum value
hdac_hdmi_set_pin_port_mux() uses the written enum value to index the
texts array before calling snd_soc_dapm_put_enum_double(), which validates
that the value is within the enum item range.
An out-of-range value can therefore make the driver read past the texts
array before the helper rejects the write. Move the lookup after the helper
has accepted the value. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Release the HW‑provided UAR index rather than the SW one
Free the UAR index returned by the hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
xprtrdma: Decouple req recycling from RPC completion
rl_kref formerly served two distinct lifetimes through a single
refcount: it gated when a Reply could wake its RPC task, and it
gated when an rpcrdma_req could return to its free pool. The
marshal path took the Send-side reference only when SGEs needed
DMA-unmap (sc_unmap_count > 0), which made a Send carrying only
pre-registered buffers an exception: the Reply handler dropped
rl_kref from 1 to 0 and freed the req while the HCA might still
be DMA-reading from its send buffer.
Give rl_kref a narrower job. The RPC layer takes one reference
when slot allocation hands a req out. rpcrdma_prepare_send_sges()
takes a Send-side reference unconditionally after WR preparation
succeeds. xprt_rdma_free_slot() and xprt_rdma_bc_free_rqst() drop
the RPC-layer reference; rpcrdma_sendctx_unmap() drops the
Send-side reference. The req returns to its free pool only after
both owners have signed off.
The existing kref_init(&req->rl_kref) call in
rpcrdma_prepare_send_sges() is removed. Initialization moves to
the slot-allocation paths (xprt_rdma_alloc_slot and
rpcrdma_bc_rqst_get), and the release callback re-arms rl_kref
before the req returns to a free pool. A re-init in the marshal
path would discard the RPC-layer reference that already exists
on entry.
Three invariants follow:
- Any rpcrdma_req held by an rpc_rqst has rl_kref >= 1.
xprt_rdma_alloc_slot(), rpcrdma_bc_rqst_get(), and the
backlog-wake branch in xprt_rdma_alloc_slot() each kref_init
rl_kref before publishing the req. Without this invariant,
an RPC task that aborts between slot allocation and marshal
(gss_refresh failure or signal during call_connect, for
example) would drive xprt_release() ->
xprt_rdma_free_slot() -> kref_put against a refcount of
zero, saturating refcount_t and stranding the slot.
- The Send-side reference is taken only after WR prep
succeeds. A mapping failure in rpcrdma_prepare_send_sges()
runs rpcrdma_sendctx_cancel(), which DMA-unmaps the sendctx
and clears sc_req without touching rl_kref. The sendctx
ring walks in rpcrdma_sendctx_put_locked() and
rpcrdma_sendctxs_destroy() skip entries with sc_req == NULL,
so a burst of -EIO marshal failures cannot hold reqs off
rb_send_bufs.
- The release callback re-arms rl_kref so the next consumer
enters with the invariant satisfied.
Replies now complete the RPC directly. rpcrdma_reply_handler()
calls rpcrdma_complete_rqst() in place of kref_put on the
non-LocalInv branch. The LocalInv branch already completes the
RPC from frwr_unmap_async() and is unaffected.
Because Send-side references can now outlive RPC completion,
connection teardown drains sendctx entries whose unsignaled
Sends never had a later signaled completion to walk the ring.
rpcrdma_sendctxs_destroy() walks the active range and runs
rpcrdma_sendctx_unmap() on each entry with a non-NULL sc_req
before the request buffers are reset, and is moved ahead of
rpcrdma_reqs_reset() in rpcrdma_xprt_disconnect() so the reqs
are still in their pre-reset state when the Send-side refs are
released.
The drain creates a teardown-ordering hazard on the backchannel
path. With the new lifetime, releasing a bc_prealloc req from
rpcrdma_req_release() re-adds it to bc_pa_list. The disconnect
in xprt_rdma_destroy() runs after xprt_destroy_backchannel() has
already emptied bc_pa_list, so the drained reqs would otherwise
leak. xprt_rdma_destroy() now runs xprt_rdma_bc_destroy(xprt, 0)
a second time after the disconnect to reclaim them. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: Fix possible use after free
In dma_release_channel(), check chan->device->privatecnt after call
dma_chan_put(). However, dma_chan_put() call dma_device_put() which could
release the last reference of the device if the DMA provider is already
gone and hence free it.
Fixes it by moving dma_chan_put() after the check. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: call _ntfs_bad_inode() when failing to rename
It is safe to call _ntfs_bad_inode on live inodes since:
commit 519b078998ce ("fs/ntfs3: Exclude call make_bad_inode for live nodes.")
The WARN_ON was added when it wasn't safe by:
commit d99208b91933 ("fs/ntfs3: cancle set bad inode after removing name fails")
Replace the WARN_ON with a call to _ntfs_bad_inode() to prevent further
operations on the inconsistent inode. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: add bounds check to run_get_highest_vcn()
run_get_highest_vcn() parses a packed NTFS mapping-pairs buffer without
any length bound, relying solely on a 0x00 terminator to stop. A
crafted $LogFile UpdateMappingPairs record whose embedded attribute
contains mapping-pairs runs without a terminator causes the function to
read past the slab allocation, triggering a KASAN slab-out-of-bounds
read on mount.
The sibling function run_unpack() received an analogous bounds-check in
commit b62567bca474 ("ntfs3: add buffer boundary checks to run_unpack()"),
but run_get_highest_vcn() was missed.
Take a run_buf_size parameter and reject any run header whose payload
would extend past the buffer end, mirroring the pattern used by
run_unpack(). The caller in fslog.c passes the remaining attribute
bytes after the mapping-pairs offset.
KASAN report (on mainline v7.1 merge window HEAD):
BUG: KASAN: slab-out-of-bounds in run_get_highest_vcn+0x3c0/0x410
Read of size 1 at addr ffff88800e2d5400 by task mount/72
Call Trace:
run_get_highest_vcn+0x3c0/0x410
do_action.isra.0+0x3ba8/0x7b50
log_replay+0x9ddd/0x10200
ntfs_loadlog_and_replay+0x4ad/0x610
ntfs_fill_super+0x214a/0x4540 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: mma8452: handle I2C read error(s) in mma8452_read()
Currently, If i2c_smbus_read_i2c_block_data() fails but
mma8452_set_runtime_pm_state() succeeds, mma8452_read() returns 0.
As a result, the caller mma8452_read_raw() assumes the read was
successful and proceeds to use a buffer containing uninitialized
stack memory.
Add proper checking of the I2C read return value and propagate errors
to the caller. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: xilinx-ams: fix out-of-bounds channel lookup in event handling
ams_event_to_channel() may return a pointer past the end of
dev->channels when no matching scan_index is found. This can lead
to invalid memory access in ams_handle_event().
Add a bounds check in ams_event_to_channel() and return NULL when
no channel is found. Also guard the caller to safely handle this
case. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Fix UAF in hci_unregister_dev()
hci_unregister_dev() does not disable cmd_timer and ncmd_timer
before the hci_dev structure is freed. If a timeout fires
during device teardown, the callback dereferences freed memory
(including the hdev->reset function pointer), leading to a
use-after-free.
Add disable_delayed_work_sync() calls alongside the existing
disable_work_sync() calls to ensure both timers are fully
quiesced before teardown proceeds. |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/qat: fix f_pos race in qat_vf_resume_write()
qat_vf_resume_write() checks filp->f_pos before taking migf->lock, but
copies into the migration-state buffer after taking the lock and
re-reading the shared file position.
Two concurrent writers could therefore pass the bounds check with the
old offset, then have the second writer copy after the first advanced
f_pos, writing past the end of the migration-state buffer.
Take migf->lock before doing the boundary checks. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix kernel BUG in ext4_write_inline_data_end
When the data=journal mount option is used, the ext4_journalled_write_end()
function incorrectly calls ext4_write_inline_data_end() without checking
if the EXT4_STATE_MAY_INLINE_DATA flag is still set on the inode.
If a previous attempt to convert the inline data to an extent failed (e.g.
due to ENOSPC), the EXT4_STATE_MAY_INLINE_DATA flag is cleared, but
the EXT4_INODE_INLINE_DATA flag remains set. In this scenario, the next
call to ext4_write_begin() will not prepare the inline data xattr for
writing, but ext4_journalled_write_end() will incorrectly attempt to write
to it, triggering a BUG_ON(pos + len > EXT4_I(inode)->i_inline_size) in
ext4_write_inline_data() since i_inline_size was not expanded.
Fix this by ensuring that ext4_journalled_write_end() only calls
ext4_write_inline_data_end() if the EXT4_STATE_MAY_INLINE_DATA flag is
set, mirroring the behavior of ext4_write_end() and ext4_da_write_end(). |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa/octeon_ep: fix IRQ-to-ring mapping in interrupt handler
Look up the IRQ index in oct_hw->irqs instead of assuming
irq - irqs[0]. This supports non-contiguous IRQ numbers and
avoids incorrect ring indexing when irqs[0] is not the base. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio: rtc: tear down old virtqueues before restore
virtio_device_restore() resets the device and restores the negotiated
features before calling ->restore(). viortc_freeze() intentionally
leaves the existing virtqueues in place so the alarm queue can still
wake the system, but viortc_restore() immediately calls
viortc_init_vqs() without first deleting those old queues.
If virtqueue reinitialization fails on virtio-pci, the transport error
path can run vp_del_vqs() against a newly allocated vp_dev->vqs array
while vdev->vqs still contains the old virtqueues. vp_del_vqs() then
looks up queue state through the new array and can dereference a NULL
info pointer in vp_del_vq(), crashing the guest kernel during restore.
This can also happen during a non-faulty reinitialization, when one of
the vp_find_vqs_msix() attempts is unsuccessful before a later attempt
would succeed.
Delete the stale virtqueues before rebuilding them. If restore fails
before virtio_device_ready(), reuse the remove path to stop the device.
Once the device is ready, return errors directly instead of deleting the
virtqueues again. |
