| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
e1000: Move cancel_work_sync to avoid deadlock
Previously, e1000_down called cancel_work_sync for the e1000 reset task
(via e1000_down_and_stop), which takes RTNL.
As reported by users and syzbot, a deadlock is possible in the following
scenario:
CPU 0:
- RTNL is held
- e1000_close
- e1000_down
- cancel_work_sync (cancel / wait for e1000_reset_task())
CPU 1:
- process_one_work
- e1000_reset_task
- take RTNL
To remedy this, avoid calling cancel_work_sync from e1000_down
(e1000_reset_task does nothing if the device is down anyway). Instead,
call cancel_work_sync for e1000_reset_task when the device is being
removed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix uaf in ath12k_core_init()
When the execution of ath12k_core_hw_group_assign() or
ath12k_core_hw_group_create() fails, the registered notifier chain is not
unregistered properly. Its memory is freed after rmmod, which may trigger
to a use-after-free (UAF) issue if there is a subsequent access to this
notifier chain.
Fixes the issue by calling ath12k_core_panic_notifier_unregister() in
failure cases.
Call trace:
notifier_chain_register+0x4c/0x1f0 (P)
atomic_notifier_chain_register+0x38/0x68
ath12k_core_init+0x50/0x4e8 [ath12k]
ath12k_pci_probe+0x5f8/0xc28 [ath12k]
pci_device_probe+0xbc/0x1a8
really_probe+0xc8/0x3a0
__driver_probe_device+0x84/0x1b0
driver_probe_device+0x44/0x130
__driver_attach+0xcc/0x208
bus_for_each_dev+0x84/0x100
driver_attach+0x2c/0x40
bus_add_driver+0x130/0x260
driver_register+0x70/0x138
__pci_register_driver+0x68/0x80
ath12k_pci_init+0x30/0x68 [ath12k]
ath12k_init+0x28/0x78 [ath12k]
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: Protect mgmt_pending list with its own lock
This uses a mutex to protect from concurrent access of mgmt_pending
list which can cause crashes like:
==================================================================
BUG: KASAN: slab-use-after-free in hci_sock_get_channel+0x60/0x68 net/bluetooth/hci_sock.c:91
Read of size 2 at addr ffff0000c48885b2 by task syz.4.334/7318
CPU: 0 UID: 0 PID: 7318 Comm: syz.4.334 Not tainted 6.15.0-rc7-syzkaller-g187899f4124a #0 PREEMPT
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025
Call trace:
show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:466 (C)
__dump_stack+0x30/0x40 lib/dump_stack.c:94
dump_stack_lvl+0xd8/0x12c lib/dump_stack.c:120
print_address_description+0xa8/0x254 mm/kasan/report.c:408
print_report+0x68/0x84 mm/kasan/report.c:521
kasan_report+0xb0/0x110 mm/kasan/report.c:634
__asan_report_load2_noabort+0x20/0x2c mm/kasan/report_generic.c:379
hci_sock_get_channel+0x60/0x68 net/bluetooth/hci_sock.c:91
mgmt_pending_find+0x7c/0x140 net/bluetooth/mgmt_util.c:223
pending_find net/bluetooth/mgmt.c:947 [inline]
remove_adv_monitor+0x44/0x1a4 net/bluetooth/mgmt.c:5445
hci_mgmt_cmd+0x780/0xc00 net/bluetooth/hci_sock.c:1712
hci_sock_sendmsg+0x544/0xbb0 net/bluetooth/hci_sock.c:1832
sock_sendmsg_nosec net/socket.c:712 [inline]
__sock_sendmsg net/socket.c:727 [inline]
sock_write_iter+0x25c/0x378 net/socket.c:1131
new_sync_write fs/read_write.c:591 [inline]
vfs_write+0x62c/0x97c fs/read_write.c:684
ksys_write+0x120/0x210 fs/read_write.c:736
__do_sys_write fs/read_write.c:747 [inline]
__se_sys_write fs/read_write.c:744 [inline]
__arm64_sys_write+0x7c/0x90 fs/read_write.c:744
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49
el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132
do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151
el0_svc+0x58/0x17c arch/arm64/kernel/entry-common.c:767
el0t_64_sync_handler+0x78/0x108 arch/arm64/kernel/entry-common.c:786
el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:600
Allocated by task 7037:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x40/0x78 mm/kasan/common.c:68
kasan_save_alloc_info+0x44/0x54 mm/kasan/generic.c:562
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x9c/0xb4 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__do_kmalloc_node mm/slub.c:4327 [inline]
__kmalloc_noprof+0x2fc/0x4c8 mm/slub.c:4339
kmalloc_noprof include/linux/slab.h:909 [inline]
sk_prot_alloc+0xc4/0x1f0 net/core/sock.c:2198
sk_alloc+0x44/0x3ac net/core/sock.c:2254
bt_sock_alloc+0x4c/0x300 net/bluetooth/af_bluetooth.c:148
hci_sock_create+0xa8/0x194 net/bluetooth/hci_sock.c:2202
bt_sock_create+0x14c/0x24c net/bluetooth/af_bluetooth.c:132
__sock_create+0x43c/0x91c net/socket.c:1541
sock_create net/socket.c:1599 [inline]
__sys_socket_create net/socket.c:1636 [inline]
__sys_socket+0xd4/0x1c0 net/socket.c:1683
__do_sys_socket net/socket.c:1697 [inline]
__se_sys_socket net/socket.c:1695 [inline]
__arm64_sys_socket+0x7c/0x94 net/socket.c:1695
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49
el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132
do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151
el0_svc+0x58/0x17c arch/arm64/kernel/entry-common.c:767
el0t_64_sync_handler+0x78/0x108 arch/arm64/kernel/entry-common.c:786
el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:600
Freed by task 6607:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x40/0x78 mm/kasan/common.c:68
kasan_save_free_info+0x58/0x70 mm/kasan/generic.c:576
poison_slab_object mm/kasan/common.c:247 [inline]
__kasan_slab_free+0x68/0x88 mm/kasan/common.c:264
kasan_slab_free include/linux/kasan.h:233 [inline
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: avoid panic on init failure
In case of an error during init, in_hw_restart will be set, but it will
never get cleared.
Instead, we will retry to init again, and then we will act like we are in a
restart when we are actually not.
This causes (among others) to a NULL pointer dereference when canceling
rx_omi::finished_work, that was not even initialized, because we thought
that we are in hw_restart.
Set in_hw_restart to true only if the fw is running, then we know that
FW was loaded successfully and we are not going to the retry loop. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: reject malformed HCI_CMD_SYNC commands
In 'mgmt_hci_cmd_sync()', check whether the size of parameters passed
in 'struct mgmt_cp_hci_cmd_sync' matches the total size of the data
(i.e. 'sizeof(struct mgmt_cp_hci_cmd_sync)' plus trailing bytes).
Otherwise, large invalid 'params_len' will cause 'hci_cmd_sync_alloc()'
to do 'skb_put_data()' from an area beyond the one actually passed to
'mgmt_hci_cmd_sync()'. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: ohci-nxp: Fix refcount leak in ohci_hcd_nxp_probe
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/connector: only call HDMI audio helper plugged cb if non-null
On driver remove, sound/soc/codecs/hdmi-codec.c calls the plugged_cb
with NULL as the callback function and codec_dev, as seen in its
hdmi_remove function.
The HDMI audio helper then happily tries calling said null function
pointer, and produces an Oops as a result.
Fix this by only executing the callback if fn is non-null. This means
the .plugged_cb and .plugged_cb_dev members still get appropriately
cleared. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: Fix null-ptr-deref in mt7996_mmio_wed_init()
devm_ioremap() returns NULL on error. Currently, mt7996_mmio_wed_init()
does not check for this case, which results in a NULL pointer
dereference.
Prevent null pointer dereference in mt7996_mmio_wed_init() |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: Fix null-ptr-deref in mt7915_mmio_wed_init()
devm_ioremap() returns NULL on error. Currently, mt7915_mmio_wed_init()
does not check for this case, which results in a NULL pointer
dereference.
Prevent null pointer dereference in mt7915_mmio_wed_init(). |
| In the Linux kernel, the following vulnerability has been resolved:
coresight: holding cscfg_csdev_lock while removing cscfg from csdev
There'll be possible race scenario for coresight config:
CPU0 CPU1
(perf enable) load module
cscfg_load_config_sets()
activate config. // sysfs
(sys_active_cnt == 1)
...
cscfg_csdev_enable_active_config()
lock(csdev->cscfg_csdev_lock)
deactivate config // sysfs
(sys_activec_cnt == 0)
cscfg_unload_config_sets()
<iterating config_csdev_list> cscfg_remove_owned_csdev_configs()
// here load config activate by CPU1
unlock(csdev->cscfg_csdev_lock)
iterating config_csdev_list could be raced with config_csdev_list's
entry delete.
To resolve this race , hold csdev->cscfg_csdev_lock() while
cscfg_remove_owned_csdev_configs() |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad4851: fix ad4858 chan pointer handling
The pointer returned from ad4851_parse_channels_common() is incremented
internally as each channel is populated. In ad4858_parse_channels(),
the same pointer was further incremented while setting ext_scan_type
fields for each channel. This resulted in indio_dev->channels being set
to a pointer past the end of the allocated array, potentially causing
memory corruption or undefined behavior.
Fix this by iterating over the channels using an explicit index instead
of incrementing the pointer. This preserves the original base pointer
and ensures all channel metadata is set correctly. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: acpi: Prevent null pointer dereference in usb_acpi_add_usb4_devlink()
As demonstrated by the fix for update_port_device_state,
commit 12783c0b9e2c ("usb: core: Prevent null pointer dereference in update_port_device_state"),
usb_hub_to_struct_hub() can return NULL in certain scenarios,
such as during hub driver unbind or teardown race conditions,
even if the underlying usb_device structure exists.
Plus, all other places that call usb_hub_to_struct_hub() in the same file
do check for NULL return values.
If usb_hub_to_struct_hub() returns NULL, the subsequent access to
hub->ports[udev->portnum - 1] will cause a null pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/pwrctrl: Cancel outstanding rescan work when unregistering
It's possible to trigger use-after-free here by:
(a) forcing rescan_work_func() to take a long time and
(b) utilizing a pwrctrl driver that may be unloaded for some reason
Cancel outstanding work to ensure it is finished before we allow our data
structures to be cleaned up.
[bhelgaas: tidy commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
dm: limit swapping tables for devices with zone write plugs
dm_revalidate_zones() only allowed new or previously unzoned devices to
call blk_revalidate_disk_zones(). If the device was already zoned,
disk->nr_zones would always equal md->nr_zones, so dm_revalidate_zones()
returned without doing any work. This would make the zoned settings for
the device not match the new table. If the device had zone write plug
resources, it could run into errors like bdev_zone_is_seq() reading
invalid memory because disk->conv_zones_bitmap was the wrong size.
If the device doesn't have any zone write plug resources, calling
blk_revalidate_disk_zones() will always correctly update device. If
blk_revalidate_disk_zones() fails, it can still overwrite or clear the
current disk->nr_zones value. In this case, DM must restore the previous
value of disk->nr_zones, so that the zoned settings will continue to
match the previous value that it fell back to.
If the device already has zone write plug resources,
blk_revalidate_disk_zones() will not correctly update them, if it is
called for arbitrary zoned device changes. Since there is not much need
for this ability, the easiest solution is to disallow any table reloads
that change the zoned settings, for devices that already have zone plug
resources. Specifically, if a device already has zone plug resources
allocated, it can only switch to another zoned table that also emulates
zone append. Also, it cannot change the device size or the zone size. A
device can switch to an error target. |
| In the Linux kernel, the following vulnerability has been resolved:
watchdog: lenovo_se30_wdt: Fix possible devm_ioremap() NULL pointer dereference in lenovo_se30_wdt_probe()
devm_ioremap() returns NULL on error. Currently, lenovo_se30_wdt_probe()
does not check for this case, which results in a NULL pointer
dereference.
Add NULL check after devm_ioremap() to prevent this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: clear phydev->devlink when the link is deleted
There is a potential crash issue when disabling and re-enabling the
network port. When disabling the network port, phy_detach() calls
device_link_del() to remove the device link, but it does not clear
phydev->devlink, so phydev->devlink is not a NULL pointer. Then the
network port is re-enabled, but if phy_attach_direct() fails before
calling device_link_add(), the code jumps to the "error" label and
calls phy_detach(). Since phydev->devlink retains the old value from
the previous attach/detach cycle, device_link_del() uses the old value,
which accesses a NULL pointer and causes a crash. The simplified crash
log is as follows.
[ 24.702421] Call trace:
[ 24.704856] device_link_put_kref+0x20/0x120
[ 24.709124] device_link_del+0x30/0x48
[ 24.712864] phy_detach+0x24/0x168
[ 24.716261] phy_attach_direct+0x168/0x3a4
[ 24.720352] phylink_fwnode_phy_connect+0xc8/0x14c
[ 24.725140] phylink_of_phy_connect+0x1c/0x34
Therefore, phydev->devlink needs to be cleared when the device link is
deleted. |
| An out-of-bounds read vulnerability was found in Netfilter Connection Tracking (conntrack) in the Linux kernel. This flaw allows a remote user to disclose sensitive information via the DCCP protocol. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: max77705: Fix workqueue error handling in probe
The create_singlethread_workqueue() doesn't return error pointers, it
returns NULL. Also cleanup the workqueue on the error paths. |
| ImageMagick is a free and open-source software suite, used for editing and manipulating digital images. The `AppImage` version `ImageMagick` might use an empty path when setting `MAGICK_CONFIGURE_PATH` and `LD_LIBRARY_PATH` environment variables while executing, which might lead to arbitrary code execution by loading malicious configuration files or shared libraries in the current working directory while executing `ImageMagick`. The vulnerability is fixed in 7.11-36. |
| A NULL pointer dereference flaw was found in dbFree in fs/jfs/jfs_dmap.c in the journaling file system (JFS) in the Linux Kernel. This issue may allow a local attacker to crash the system due to a missing sanity check. |
