| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: harden runlist realloc size calculations
Add a shared helper to safely convert runlist element counts to byte sizes
using overflow checks, and use it in both ntfs_rl_realloc() and
ntfs_rl_realloc_nofail(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_sip: widen NAT rewrite delta to s32 in sip_help_tcp()
sip_help_tcp() stores the size change of each NAT-rewritten SIP message
in s16 diff and accumulates it in s16 tdiff, but a single message can
grow by more than S16_MAX while the packet stays under the 65535
enlarge_skb() limit: nf_nat_sip() rewrites every matching URI, and a long
Contact list expands the message by tens of kilobytes. diff then wraps,
and "datalen = datalen + diff - msglen" yields a huge unsigned datalen,
so the next iteration's ct_sip_get_header() reads past the linearized skb
tail.
Widen diff, tdiff and the seq_adjust hook to s32. Both are bounded by the
65535 byte packet limit, and the seqadj core is already s32
(nf_ct_seqadj_set() takes s32), so no previously accepted input is
rejected.
BUG: KASAN: use-after-free in ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
Read of size 1 at addr ffff888010800000 by task ksoftirqd/1/25
ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
sip_help_tcp (net/netfilter/nf_conntrack_sip.c:1694)
nf_confirm (net/netfilter/nf_conntrack_proto.c:183)
nf_hook_slow (net/netfilter/core.c:619)
ip6_output (net/ipv6/ip6_output.c:246)
ip6_forward (net/ipv6/ip6_output.c:690)
ipv6_rcv (net/ipv6/ip6_input.c:351)
__netif_receive_skb_one_core (net/core/dev.c:6212)
process_backlog (net/core/dev.c:6676)
__napi_poll (net/core/dev.c:7735)
net_rx_action (net/core/dev.c:7955)
handle_softirqs (kernel/softirq.c:622)
run_ksoftirqd (kernel/softirq.c:1076)
... |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: vgic: Fix race between LPI release and re-registration
Fix a potential race between decrementing an LPI's reference count and
evicting that structure from the LPI xarray.
LPI structures are maintained in the VGIC LPI xarray (dist->lpi_xa).
When the reference count of an LPI structure drops to zero,
vgic_release_lpi_locked() removes the structure from the xarray and
frees it under the xarray lock.
However, the release of an LPI can race with a concurrent LPI
re-registration with the same INTID via vgic_add_lpi() on another CPU,
since the reference count drop and the xarray eviction are not performed
in a single atomic step. This can happen e.g. if the guest issues a
DISCARD while the LPI is still referenced from a vCPU's active-pending
list (ap_list), and the same INTID is re-mapped via MAPTI.
Particularly, vgic_release_lpi_locked() is called from two distinct
paths: direct release via vgic_put_irq(), and deferred release via
vgic_release_deleted_lpis(). During direct release, the issue can result
in deleting a newly registered LPI from the xarray:
CPU0 (Releasing LPI) CPU1 (Adding new LPI)
==================== =====================
vgic_put_irq()
__vgic_put_irq()
refcount_dec_and_test()
vgic_add_lpi()
xa_lock_irqsave()
old_irq = xa_load(.., intid)
vgic_try_get_irq_ref(old_irq) == false
new IRQ inserted --> __xa_store(.., intid, ..)
xa_unlock_irqrestore()
xa_lock_irqsave();
vgic_release_lpi_locked()
__xa_erase(.., irq->intid) <-- BUG: new IRQ is erased
kfree_rcu(old_irq)
During the deferred release path, the old IRQ can be leaked:
CPU0 (Releasing LPI) CPU1 (Adding new LPI)
==================== =====================
vgic_put_irq_norelease()
__vgic_put_irq()
refcount_dec_and_test()
irq->pending_release = true
vgic_add_lpi()
xa_lock_irqsave()
old_irq = xa_load(.., intid)
vgic_try_get_irq_ref(oldirq) == false
BUG: old IRQ overwritten --> __xa_store(.., intid, ..)
xa_unlock_irqrestore()
vgic_release_deleted_lpis()
xa_lock_irqsave()
xa_for_each() { .. } <-- old IRQ with pending_release = true
is gone, so it cannot be released
To fix the direct release path, move the reference count drop inside
the xarray lock, making sure that vgic_add_lpi() never encounters the
to-be-released LPI.
In the deferred release path, the refcount drop must happen under a raw
spinlock, so the xarray lock cannot be grabbed, and the same solution
does not work. Instead, update vgic_add_lpi(), so that if it evicts
an LPI from the xarray, it takes on the responsibility of freeing it.
Consequently, an LPI may now be freed concurrently after a deferred
release drops the refcount, so accessing the pending_release field is no
longer safe from use-after-free. Delete all uses of the flag, and update
vgic_release_deleted_lpis() to identify orphaned LPIs purely based on
their refcount. |
| In the Linux kernel, the following vulnerability has been resolved:
keys: fix out-of-bounds read in keyring_get_key_chunk()
For description-level chunks keyring_get_key_chunk() advances the read
pointer by level * sizeof(long) past the inline prefix but only
bounds-checks the prefix, so a long enough key description is read past
its kmemdup(desc, desc_len + 1) allocation. Compute the full byte
offset and bounds-check the description against it before reading.
The walk only reaches a description-level chunk when two keys collide
through the hash, x, type and domain_tag chunks, so this is reached from
an unprivileged add_key(2) with a crafted pair of same-type keys whose
index hashes collide; KASAN reports a slab-out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
keys: make keyring key-chunk byte order agree with keyring_diff_objects()
keyring_get_key_chunk() loads description bytes into the index chunk low
address first, while keyring_diff_objects() numbers the first differing
bit from the low end and folds the absolute byte index into the level
without removing the inline-prefix offset the level already carries.
The two disagree on byte order and bit position, so the array can be
told two keys first differ at a bit that does not differ in the chunk
the walker uses, letting crafted descriptions collide into one node.
Load the chunk in the order keyring_diff_objects() assumes and drop the
inline-prefix length when folding the byte index into the level. This
only changes the in-memory ordering used to place keys within a keyring;
add, search and read of non-colliding keys are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: make nft_object rhltable per table
The nft_object rhltable is global, this allows for accessing objects
that are being dismangled from lookup path by other existing netns.
Given the nft_obj_destroy() releases the object inmediately, this might
lead to use-after-free of these objects that are being released.
Make the existing rhltable per table to address this issue to deal with
with the nft_rcv_nl_event() path too.
Update nft_obj_lookup() to take the table as non-const, otherwise,
compiler complains when passing the objname_ht to rhltable_lookup(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_hashlimit: validate hashtable supports XT_HASHLIMIT_RATE_MATCH
The XT_HASHLIMIT_RATE_MATCH flag mode changes the semantics of the
dsthash_ent structure which represents an entry in the hashtable. There
is a union area which uses a different layout to express the rate match
mode.
Update .checkentry path to validate the XT_HASHLIMIT_RATE_MATCH mode
flag is requested by two or more different rules that refer to the same
hashtable. Otherwise, uninitialized access to the burst field in the
union is possible.
Reject the use of the XT_HASHLIMIT_RATE_MATCH mode flag if set on by
revision less than 3 too. |
| In the Linux kernel, the following vulnerability has been resolved:
rds: tcp: hold the RCU lock across ipv6_chk_addr() in rds_tcp_laddr_check()
rds_tcp_laddr_check() looks up a scoped IPv6 interface with
dev_get_by_index_rcu(), drops the RCU read-side lock, and only then
passes the bare struct net_device * into ipv6_chk_addr().
dev_get_by_index_rcu() only keeps the device alive within the same RCU
read-side section. After rcu_read_unlock(), a concurrent RTM_DELLINK can
free the net_device; ipv6_chk_addr() then dereferences the stale pointer
in __ipv6_chk_addr_and_flags() (e.g. l3mdev_master_dev_rcu(dev)), reading
freed memory.
Keep the RCU read-side lock held across the ipv6_chk_addr() call instead
of dropping it right after the lookup, so the device cannot be freed
while it is in use.
BUG: KASAN: slab-use-after-free in __ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
Read of size 8 at addr ffff8880106ec000 by task exploit/153
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
__ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
ipv6_chk_addr (net/ipv6/addrconf.c:2031 net/ipv6/addrconf.c:1972)
rds_tcp_laddr_check (net/rds/tcp.c:370)
rds_bind (net/rds/bind.c:248)
__sys_bind (net/socket.c:1920)
__x64_sys_bind (net/socket.c:1956)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) |
| In the Linux kernel, the following vulnerability has been resolved:
nexthop: take nh->lock for f6i_list walks in replace check and notify
fib6_check_nh_list() and __nexthop_replace_notify() walk nh->f6i_list
during an RTNL-serialized nexthop replace without holding nh->lock. IPv6
RTM_NEWROUTE/RTM_DELROUTE run without RTNL and mutate that list under
nh->lock (fib6_add_rt2node_nh(), fib6_purge_rt()), so both walks race a
concurrent route delete that unlinks and frees a fib6_info:
BUG: KASAN: slab-use-after-free in rt6_fill_node.isra.0 (net/ipv6/route.c:5799)
Read of size 4 at addr ffff888014607e64 by task exploit/143
rt6_fill_node.isra.0 (net/ipv6/route.c:5799)
fib6_rt_update (net/ipv6/route.c:6412)
__nexthop_replace_notify (net/ipv4/nexthop.c:2542)
rtm_new_nexthop (net/ipv4/nexthop.c:2554)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
BUG: KASAN: slab-use-after-free in fib6_check_nh_list (net/ipv4/nexthop.c:1605)
Read of size 8 at addr ffff888014a7d068 by task exploit/142
fib6_check_nh_list (net/ipv4/nexthop.c:1605)
rtm_new_nexthop (net/ipv4/nexthop.c:2575)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
Both walks only read the entries and take no tb6_lock, so protect them
with nh->lock; fib6_rt_update() uses gfp_any(), which returns GFP_ATOMIC
under the lock. |
| In the Linux kernel, the following vulnerability has been resolved:
nexthop: avoid unlocked f6i_list walk in nh_rt_cache_flush
nh_rt_cache_flush() walks nh->f6i_list during an RTNL-serialized nexthop
replace without holding nh->lock, racing the unlocked IPv6 route
add/delete that mutate the list under nh->lock and free fib6_info
entries (nh_rt_cache_flush() is inlined into rtm_new_nexthop()):
BUG: KASAN: slab-use-after-free in nh_rt_cache_flush (net/ipv4/nexthop.c:2243)
Read of size 8 at addr ffff888012953e18 by task exploit/146
nh_rt_cache_flush (net/ipv4/nexthop.c:2243)
replace_nexthop (net/ipv4/nexthop.c:2610)
rtm_new_nexthop (net/ipv4/nexthop.c:3323)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
Unlike the other f6i_list walks, this one bumps each route's sernum via
fib6_update_sernum_upto_root(), which needs tb6_lock; taking nh->lock
around it would invert the established tb6_lock -> nh->lock order and
deadlock. As the only purpose is to invalidate cached dsts, bump the
IPv6 sernum for the whole netns with rt_genid_bump_ipv6() instead,
mirroring the rt_cache_flush() already done for IPv4 just above. |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: fix buffer leak in xsk_drop_skb() for AF_XDP multi-buffer Tx
This patch is inspired by the check[1] from sashiko. It says when
overflow happens, the address of cq to be published is invalid.
Actually the severer thing is the whole process of publishing the
address of cq in this particular case is not right: it should truely
publish the address and advance the cached_prod in cq as long as it
reads descriptors from txq.
The following is the full analysis.
xsk_drop_skb() is called in three places, which all discard a partially
built multi-buffer skb:
1) xsk_build_skb() -EOVERFLOW error path: packet exceeds MAX_SKB_FRAGS
2) __xsk_generic_xmit() post-loop cleanup: an invalid descriptor in
the TX ring prevents the partial packet from completing
3) xsk_release(): socket close while xs->skb holds an incomplete packet
In all three cases, the TX descriptors for the already-processed frags
have been consumed from the TX ring (xskq_cons_release), and CQ slots
have been reserved. However, xsk_drop_skb() calls xsk_consume_skb()
which cancels the CQ reservations via xsk_cq_cancel_locked(). Since
the buffer addresses never appear in the completion queue, userspace
permanently loses track of these buffers.
Fix this by letting consume_skb() trigger the existing xsk_destruct_skb
destructor, which already submits buffer addresses to the CQ via
xsk_cq_submit_addr_locked().
Note that cancelling the descriptors back to the TX ring (via
xskq_cons_cancel_n) is not a appropriate option because an oversized
packet that always exceeds MAX_SKB_FRAGS would be retried indefinitely,
which is an obviously deadlock bug in the TX path.
Also move the desc->addr assignment in xsk_build_skb() above the
overflow check so that the current descriptor's address is recorded
before a potential -EOVERFLOW jump to free_err, consistent with the
zerocopy path in xsk_build_skb_zerocopy().
[1]: https://lore.kernel.org/all/20260425041726.85FB3C2BCB2@smtp.kernel.org/ |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: drain continuation descs after overflow in xsk_build_skb()
Fix generic xmit path multi-buffer logic when packets are either too big
(count of descriptors exceed MAX_SKB_FRAGS) or an invalid descriptor is
included in fragmented packet. Introduce xdp_sock::drain_cont and act
upon this flag - when it is set, keep on consuming descriptors from
AF_XDP Tx ring and put them directly onto Cq. Previously these
descriptors were silently lost and could never be reached again. |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: reclaim invalid Tx descriptors in ZC batch path
The zero-copy Tx batch parser stops when it encounters an invalid
descriptor. If this happens after one or more continuation descriptors,
the Tx consumer can be advanced past fragments that are neither submitted
to the driver nor returned to userspace through the completion ring.
A similar problem occurs when a packet exceeds xdp_zc_max_segs. The
descriptors consumed up to the limit are released without completion, and
the remaining continuation descriptors can subsequently be interpreted
as the beginning of another packet.
Parse Tx batches in packet units and distinguish descriptors belonging to
complete valid packets from descriptors consumed while draining an
invalid or oversized packet. Return the former to the driver and append
the latter to the CQ address area so userspace can reclaim their UMEM
frames.
Treat a standalone invalid descriptor as a one-descriptor reclaim-only
packet. Advancing the Tx-ring consumer releases the ring slot, but does
not by itself return ownership of the referenced UMEM frame to userspace.
Once draining starts, continue until the packet's end-of-packet
descriptor is consumed. Preserve the drain state on the socket when EOP
has not yet been supplied, so draining can continue during a later call.
Leave incomplete but otherwise valid packets on the Tx ring.
Shared-UMEM pools using multi-buffer Tx also need packet-framed parsing.
Walk their Tx sockets one packet at a time, preserving the existing
per-socket fairness scheme, instead of using the legacy one-descriptor
fallback. Keep that fallback for shared pools that do not use
multi-buffer Tx. Since the drain state is maintained per socket and both
the singular and shared paths can resume an interrupted drain, changing
the socket list from singular to shared requires no special bind-time
transition.
CQ entries are positional, and drivers may complete only part of the Tx
work returned by xsk_tx_peek_release_desc_batch(). Therefore, reclaim-only
entries cannot be published immediately when earlier driver-visible
descriptors are still outstanding.
Track the number of driver-visible CQ entries preceding the reclaim
entries. Let xsk_tx_completed() publish partial hardware Tx completions,
and publish the reclaim entries only after every earlier Tx descriptor
has completed. Complete a reclaim-only batch immediately when there is no
driver-visible work in front of it, and prevent another Tx batch from
being appended while reclaim entries remain pending.
Also cap batch processing by the size of the pool's temporary descriptor
array, as Tx rings belonging to sockets sharing a UMEM may have different
sizes.
This ensures that every invalid Tx descriptor consumed by the ZC batch
path is either submitted to the driver as part of a valid packet or
returned to userspace without violating CQ completion ordering. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi: Fix stale-data leak into the SCSI sense buffer
iscsi_scsi_cmd_rsp() copies the sense data of a SCSI Response from the
target-supplied data segment. The segment carries a 2-byte sense length
followed by the sense bytes, so it must hold 2 + senselen bytes, but the
bounds check only requires datalen >= senselen:
senselen = get_unaligned_be16(data);
if (datalen < senselen)
goto invalid_datalen;
memcpy(sc->sense_buffer, data + 2,
min_t(uint16_t, senselen, SCSI_SENSE_BUFFERSIZE));
A target that returns a SCSI Response whose datalen equals senselen
(with senselen <= SCSI_SENSE_BUFFERSIZE) makes the memcpy() from data +
2 read up to two bytes past the received data. Those bytes are stale
conn->data contents and end up in the command's sense buffer, which is
returned to userspace.
Account for the 2-byte sense length prefix in the check. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi_tcp: Bound SCSI Response data segment to the connection buffer
iscsi_tcp_hdr_dissect() receives the data segment of several PDU types
into the fixed-size conn->data buffer, which is allocated for
ISCSI_DEF_MAX_RECV_SEG_LEN (8192) bytes. For the LOGIN_RSP, TEXT_RSP,
REJECT and ASYNC_EVENT opcodes the dissect path already rejects a PDU
whose DataSegmentLength exceeds that buffer.
The SCSI Command Response (ISCSI_OP_SCSI_CMD_RSP) path also copies its
data segment (sense/response data) into conn->data via
iscsi_tcp_data_recv_prep(), but it does so without the same check. The
only upstream bound on in.datalen is conn->max_recv_dlength, the
initiator's advertised MaxRecvDataSegmentLength, which is commonly
negotiated well above 8192 (open-iscsi defaults to 262144). A target
that returns a SCSI Response with a DataSegmentLength between 8193 and
max_recv_dlength therefore overflows the 8192-byte conn->data buffer.
Once the same bound applies, ISCSI_OP_SCSI_CMD_RSP is handled exactly
like those responses: bound the data segment, receive it into conn->data
when present, and otherwise complete the PDU with no data. Fold the
opcode into that case group rather than duplicating the check. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libsas: Fix HA resume deadlock and hisi_sas disk-wake race
Commit fbefe22811c3 ("scsi: libsas: Don't always drain event workqueue
for HA resume") introduced sas_resume_ha_no_sync() to avoid a deadlock:
the PHYE_RESUME_TIMEOUT handler, running on the HA event workqueue,
calls sas_deform_port() -> sas_destruct_devices(), which removes SCSI
devices and waits for the host to become runtime-active. But the host
cannot resume until sas_resume_ha() -> sas_drain_work() returns, and the
drain is blocked on that very handler.
However skipping the drain reintroduces a race: hisi_sas returns from
resume before all PHY UP work and libsas discovery work finish. The
controller may then autosuspend while disks are still waking up. The
disks issue IO to a suspended controller, the IO fails, and the disks
get disabled.
Fix the deadlock at its source by moving the PHYE_RESUME_TIMEOUT
notification to after sas_drain_work(). By then the host resume is about
to complete, so device removal through device_link no longer blocks on
the resume and the cycle is broken.
With the deadlock gone, restore sas_resume_ha() (the draining variant)
in hisi_sas and remove sas_resume_ha_no_sync().
The reorder is safe for the other libsas consumers (isci, pm8001,
aic94xx, mvsas). During suspend, sas_suspend_devices() calls
sas_notify_lldd_dev_gone() for each device, which sets dev->lldd_dev to
NULL. When scsi_unblock_requests re-enables I/O in resume, any I/O to a
timed-out phy's disk is immediately rejected by the LLDD before reaching
hardware: isci returns SAS_DEVICE_UNKNOWN (mapped to DID_BAD_TARGET),
and pm8001 returns SAS_PHY_DOWN (mapped to DID_NO_CONNECT). Both
complete directly via scsi_done() without entering SCSI EH. This is
identical in both the old and new ordering since lldd_dev_gone runs
during suspend, before resume. The reorder only affects when the
PHYE_RESUME_TIMEOUT handler runs (synchronized by sas_drain_work()
vs. asynchronous after resume returns), not whether I/O can reach the
device. aic94xx and mvsas do not register any PM ops and never reach
this code path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix out-of-bounds clear_bit in ath12k_mac_dp_peer_cleanup()
ath12k_mac_dp_peer_cleanup() clears the ML peer ID slot on the
free_ml_peer_id_map bitmap by indexing it with dp_peer->peer_id. That is
wrong: dp_peer->peer_id for an MLO peer always carries the
ATH12K_PEER_ML_ID_VALID bit (BIT(13)), so clear_bit() is invoked with
index >= 0x2000, which is far outside the bitmap of ATH12K_MAX_MLO_PEERS
(256) bits and corrupts memory adjacent to ah->free_ml_peer_id_map. The
intended bitmap entry also never gets cleared, so subsequent
ath12k_peer_ml_alloc() calls eventually run out of IDs.
The ID without the VALID bit is what ath12k_peer_ml_alloc() returned and
is stored in ahsta->ml_peer_id. Use that instead.
While there, also reset ahsta->ml_peer_id to ATH12K_MLO_PEER_ID_INVALID so
the bitmap and ahsta->ml_peer_id stay in sync.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3 |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nct6775-core) Fix number of temperature registers for NCT6116
Unlike NCT6106, NCT6116 only has three temperature registers, and with
it only three temperature source and temperature source configuration
registers. The register addresses match those of NCT6106 and can be
re-used.
The code used a separate array to list the temperature source registers
for NCT6116, but used the size of the NCT6106 register array to set
the number of registers. The NCT6106 register array provides six addresses,
while the temperature source register array for NCT6116 only provides three
addresses. This causes a KASAN report.
BUG: KASAN: global-out-of-bounds in nct6775_probe+0x936/0x46f0 [nct6775]
Read of size 2 at addr ffffffffc19561a6 by task modprobe/954
...
Call Trace:
dump_stack+0x7d/0xa7
print_address_description.constprop.0+0x1c/0x220
? __kasan_kmalloc.constprop.0+0xc9/0xd0
? __kmalloc_node_track_caller+0x194/0x5b0
? nct6775_probe+0x936/0x46f0 [nct6775]
? nct6775_probe+0x936/0x46f0 [nct6775]
...
Fix the problem by hard-coding the number of temperature and temperature
configuration registers to three for NCT6116. Drop the unnecessary
NCT6116_REG_TEMP_SOURCE array and re-use NCT6106_REG_TEMP_SOURCE. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (lm90) Only report alarms if driver is ready
Userspace can read sysfs attributes before driver registration is complete,
immediately after devm_hwmon_device_register_with_info() has been called.
At that time, data->hwmon_dev is not yet initialized. This can trigger
a NULL pointer access since lm90_update_device() and with it
lm90_update_alarms_locked() will be called. This call schedules
report_work and lm90_report_alarms(), which passes the still-NULL
data->hwmon_dev to hwmon_notify_event() and triggers a NULL pointer
dereference.
Fix the problem by only scheduling the report and alert workers
data->hwmon_dev is set. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nzxt-smart2) DMA-align output buffer
Sashiko reports:
When send_output_report() calls hid_hw_output_report(), the underlying USB
HID core calls usb_interrupt_msg() which maps this buffer directly for DMA.
When the DMA mapping flushes or invalidates the cacheline, it will corrupt
the adjacent variables (mutex, update_interval) that were modified
concurrently by the CPU. This causes memory corruption due to cacheline
sharing on non-coherent CPU architectures (such as ARM or MIPS). The DMA
API debugging tool (CONFIG_DMA_API_DEBUG) will trigger runtime warnings
for this violation.
Any operation that triggers send_output_report() (like setting a fan speed
or updating the interval) causes the USB DMA mapping. On systems with
non-coherent caches, this structural bug causes immediate and deterministic
memory corruption.
Align the output buffer to ARCH_DMA_MINALIGN to fix the problem. |
