| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: fix array-index-out-of-bounds read in add_missing_indices
stbl is s8 but it must contain offsets into slot which can go from 0 to
127.
Added a bound check for that error and return -EIO if the check fails.
Also make jfs_readdir return with error if add_missing_indices returns
with an error. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell_rbu: Fix list usage
Pass the correct list head to list_for_each_entry*() when looping through
the packet list.
Without this patch, reading the packet data via sysfs will show the data
incorrectly (because it starts at the wrong packet), and clearing the
packet list will result in a NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
net_sched: sch_sfq: reject invalid perturb period
Gerrard Tai reported that SFQ perturb_period has no range check yet,
and this can be used to trigger a race condition fixed in a separate patch.
We want to make sure ctl->perturb_period * HZ will not overflow
and is positive.
tc qd add dev lo root sfq perturb -10 # negative value : error
Error: sch_sfq: invalid perturb period.
tc qd add dev lo root sfq perturb 1000000000 # too big : error
Error: sch_sfq: invalid perturb period.
tc qd add dev lo root sfq perturb 2000000 # acceptable value
tc -s -d qd sh dev lo
qdisc sfq 8005: root refcnt 2 limit 127p quantum 64Kb depth 127 flows 128 divisor 1024 perturb 2000000sec
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0 |
| In the Linux kernel, the following vulnerability has been resolved:
net: clear the dst when changing skb protocol
A not-so-careful NAT46 BPF program can crash the kernel
if it indiscriminately flips ingress packets from v4 to v6:
BUG: kernel NULL pointer dereference, address: 0000000000000000
ip6_rcv_core (net/ipv6/ip6_input.c:190:20)
ipv6_rcv (net/ipv6/ip6_input.c:306:8)
process_backlog (net/core/dev.c:6186:4)
napi_poll (net/core/dev.c:6906:9)
net_rx_action (net/core/dev.c:7028:13)
do_softirq (kernel/softirq.c:462:3)
netif_rx (net/core/dev.c:5326:3)
dev_loopback_xmit (net/core/dev.c:4015:2)
ip_mc_finish_output (net/ipv4/ip_output.c:363:8)
NF_HOOK (./include/linux/netfilter.h:314:9)
ip_mc_output (net/ipv4/ip_output.c:400:5)
dst_output (./include/net/dst.h:459:9)
ip_local_out (net/ipv4/ip_output.c:130:9)
ip_send_skb (net/ipv4/ip_output.c:1496:8)
udp_send_skb (net/ipv4/udp.c:1040:8)
udp_sendmsg (net/ipv4/udp.c:1328:10)
The output interface has a 4->6 program attached at ingress.
We try to loop the multicast skb back to the sending socket.
Ingress BPF runs as part of netif_rx(), pushes a valid v6 hdr
and changes skb->protocol to v6. We enter ip6_rcv_core which
tries to use skb_dst(). But the dst is still an IPv4 one left
after IPv4 mcast output.
Clear the dst in all BPF helpers which change the protocol.
Try to preserve metadata dsts, those may carry non-routing
metadata. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix null pointer dereference in destroy_previous_session
If client set ->PreviousSessionId on kerberos session setup stage,
NULL pointer dereference error will happen. Since sess->user is not
set yet, It can pass the user argument as NULL to destroy_previous_session.
sess->user will be set in ksmbd_krb5_authenticate(). So this patch move
calling destroy_previous_session() after ksmbd_krb5_authenticate(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/v3d: Avoid NULL pointer dereference in `v3d_job_update_stats()`
The following kernel Oops was recently reported by Mesa CI:
[ 800.139824] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000588
[ 800.148619] Mem abort info:
[ 800.151402] ESR = 0x0000000096000005
[ 800.155141] EC = 0x25: DABT (current EL), IL = 32 bits
[ 800.160444] SET = 0, FnV = 0
[ 800.163488] EA = 0, S1PTW = 0
[ 800.166619] FSC = 0x05: level 1 translation fault
[ 800.171487] Data abort info:
[ 800.174357] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000
[ 800.179832] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 800.184873] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 800.190176] user pgtable: 4k pages, 39-bit VAs, pgdp=00000001014c2000
[ 800.196607] [0000000000000588] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
[ 800.205305] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP
[ 800.211564] Modules linked in: vc4 snd_soc_hdmi_codec drm_display_helper v3d cec gpu_sched drm_dma_helper drm_shmem_helper drm_kms_helper drm drm_panel_orientation_quirks snd_soc_core snd_compress snd_pcm_dmaengine snd_pcm i2c_brcmstb snd_timer snd backlight
[ 800.234448] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.25+rpt-rpi-v8 #1 Debian 1:6.12.25-1+rpt1
[ 800.244182] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT)
[ 800.250005] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 800.256959] pc : v3d_job_update_stats+0x60/0x130 [v3d]
[ 800.262112] lr : v3d_job_update_stats+0x48/0x130 [v3d]
[ 800.267251] sp : ffffffc080003e60
[ 800.270555] x29: ffffffc080003e60 x28: ffffffd842784980 x27: 0224012000000000
[ 800.277687] x26: ffffffd84277f630 x25: ffffff81012fd800 x24: 0000000000000020
[ 800.284818] x23: ffffff8040238b08 x22: 0000000000000570 x21: 0000000000000158
[ 800.291948] x20: 0000000000000000 x19: ffffff8040238000 x18: 0000000000000000
[ 800.299078] x17: ffffffa8c1bd2000 x16: ffffffc080000000 x15: 0000000000000000
[ 800.306208] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
[ 800.313338] x11: 0000000000000040 x10: 0000000000001a40 x9 : ffffffd83b39757c
[ 800.320468] x8 : ffffffd842786420 x7 : 7fffffffffffffff x6 : 0000000000ef32b0
[ 800.327598] x5 : 00ffffffffffffff x4 : 0000000000000015 x3 : ffffffd842784980
[ 800.334728] x2 : 0000000000000004 x1 : 0000000000010002 x0 : 000000ba4c0ca382
[ 800.341859] Call trace:
[ 800.344294] v3d_job_update_stats+0x60/0x130 [v3d]
[ 800.349086] v3d_irq+0x124/0x2e0 [v3d]
[ 800.352835] __handle_irq_event_percpu+0x58/0x218
[ 800.357539] handle_irq_event+0x54/0xb8
[ 800.361369] handle_fasteoi_irq+0xac/0x240
[ 800.365458] handle_irq_desc+0x48/0x68
[ 800.369200] generic_handle_domain_irq+0x24/0x38
[ 800.373810] gic_handle_irq+0x48/0xd8
[ 800.377464] call_on_irq_stack+0x24/0x58
[ 800.381379] do_interrupt_handler+0x88/0x98
[ 800.385554] el1_interrupt+0x34/0x68
[ 800.389123] el1h_64_irq_handler+0x18/0x28
[ 800.393211] el1h_64_irq+0x64/0x68
[ 800.396603] default_idle_call+0x3c/0x168
[ 800.400606] do_idle+0x1fc/0x230
[ 800.403827] cpu_startup_entry+0x40/0x50
[ 800.407742] rest_init+0xe4/0xf0
[ 800.410962] start_kernel+0x5e8/0x790
[ 800.414616] __primary_switched+0x80/0x90
[ 800.418622] Code: 8b170277 8b160296 11000421 b9000861 (b9401ac1)
[ 800.424707] ---[ end trace 0000000000000000 ]---
[ 800.457313] ---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]---
This issue happens when the file descriptor is closed before the jobs
submitted by it are completed. When the job completes, we update the
global GPU stats and the per-fd GPU stats, which are exposed through
fdinfo. If the file descriptor was closed, then the struct `v3d_file_priv`
and its stats were already freed and we can't update the per-fd stats.
Therefore, if the file descriptor was already closed, don't u
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix null-ptr-deref when acquiring remote ip of ethernet bearer
The reproduction steps:
1. create a tun interface
2. enable l2 bearer
3. TIPC_NL_UDP_GET_REMOTEIP with media name set to tun
tipc: Started in network mode
tipc: Node identity 8af312d38a21, cluster identity 4711
tipc: Enabled bearer <eth:syz_tun>, priority 1
Oops: general protection fault
KASAN: null-ptr-deref in range
CPU: 1 UID: 1000 PID: 559 Comm: poc Not tainted 6.16.0-rc1+ #117 PREEMPT
Hardware name: QEMU Ubuntu 24.04 PC
RIP: 0010:tipc_udp_nl_dump_remoteip+0x4a4/0x8f0
the ub was in fact a struct dev.
when bid != 0 && skip_cnt != 0, bearer_list[bid] may be NULL or
other media when other thread changes it.
fix this by checking media_id. |
| In the Linux kernel, the following vulnerability has been resolved:
calipso: Fix null-ptr-deref in calipso_req_{set,del}attr().
syzkaller reported a null-ptr-deref in sock_omalloc() while allocating
a CALIPSO option. [0]
The NULL is of struct sock, which was fetched by sk_to_full_sk() in
calipso_req_setattr().
Since commit a1a5344ddbe8 ("tcp: avoid two atomic ops for syncookies"),
reqsk->rsk_listener could be NULL when SYN Cookie is returned to its
client, as hinted by the leading SYN Cookie log.
Here are 3 options to fix the bug:
1) Return 0 in calipso_req_setattr()
2) Return an error in calipso_req_setattr()
3) Alaways set rsk_listener
1) is no go as it bypasses LSM, but 2) effectively disables SYN Cookie
for CALIPSO. 3) is also no go as there have been many efforts to reduce
atomic ops and make TCP robust against DDoS. See also commit 3b24d854cb35
("tcp/dccp: do not touch listener sk_refcnt under synflood").
As of the blamed commit, SYN Cookie already did not need refcounting,
and no one has stumbled on the bug for 9 years, so no CALIPSO user will
care about SYN Cookie.
Let's return an error in calipso_req_setattr() and calipso_req_delattr()
in the SYN Cookie case.
This can be reproduced by [1] on Fedora and now connect() of nc times out.
[0]:
TCP: request_sock_TCPv6: Possible SYN flooding on port [::]:20002. Sending cookies.
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
CPU: 3 UID: 0 PID: 12262 Comm: syz.1.2611 Not tainted 6.14.0 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:read_pnet include/net/net_namespace.h:406 [inline]
RIP: 0010:sock_net include/net/sock.h:655 [inline]
RIP: 0010:sock_kmalloc+0x35/0x170 net/core/sock.c:2806
Code: 89 d5 41 54 55 89 f5 53 48 89 fb e8 25 e3 c6 fd e8 f0 91 e3 00 48 8d 7b 30 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 26 01 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b
RSP: 0018:ffff88811af89038 EFLAGS: 00010216
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffff888105266400
RDX: 0000000000000006 RSI: ffff88800c890000 RDI: 0000000000000030
RBP: 0000000000000050 R08: 0000000000000000 R09: ffff88810526640e
R10: ffffed1020a4cc81 R11: ffff88810526640f R12: 0000000000000000
R13: 0000000000000820 R14: ffff888105266400 R15: 0000000000000050
FS: 00007f0653a07640(0000) GS:ffff88811af80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f863ba096f4 CR3: 00000000163c0005 CR4: 0000000000770ef0
PKRU: 80000000
Call Trace:
<IRQ>
ipv6_renew_options+0x279/0x950 net/ipv6/exthdrs.c:1288
calipso_req_setattr+0x181/0x340 net/ipv6/calipso.c:1204
calipso_req_setattr+0x56/0x80 net/netlabel/netlabel_calipso.c:597
netlbl_req_setattr+0x18a/0x440 net/netlabel/netlabel_kapi.c:1249
selinux_netlbl_inet_conn_request+0x1fb/0x320 security/selinux/netlabel.c:342
selinux_inet_conn_request+0x1eb/0x2c0 security/selinux/hooks.c:5551
security_inet_conn_request+0x50/0xa0 security/security.c:4945
tcp_v6_route_req+0x22c/0x550 net/ipv6/tcp_ipv6.c:825
tcp_conn_request+0xec8/0x2b70 net/ipv4/tcp_input.c:7275
tcp_v6_conn_request+0x1e3/0x440 net/ipv6/tcp_ipv6.c:1328
tcp_rcv_state_process+0xafa/0x52b0 net/ipv4/tcp_input.c:6781
tcp_v6_do_rcv+0x8a6/0x1a40 net/ipv6/tcp_ipv6.c:1667
tcp_v6_rcv+0x505e/0x5b50 net/ipv6/tcp_ipv6.c:1904
ip6_protocol_deliver_rcu+0x17c/0x1da0 net/ipv6/ip6_input.c:436
ip6_input_finish+0x103/0x180 net/ipv6/ip6_input.c:480
NF_HOOK include/linux/netfilter.h:314 [inline]
NF_HOOK include/linux/netfilter.h:308 [inline]
ip6_input+0x13c/0x6b0 net/ipv6/ip6_input.c:491
dst_input include/net/dst.h:469 [inline]
ip6_rcv_finish net/ipv6/ip6_input.c:79 [inline]
ip6_rcv_finish+0xb6/0x490 net/ipv6/ip6_input.c:69
NF_HOOK include/linux/netfilter.h:314 [inline]
NF_HOOK include/linux/netf
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
sch_hfsc: make hfsc_qlen_notify() idempotent
hfsc_qlen_notify() is not idempotent either and not friendly
to its callers, like fq_codel_dequeue(). Let's make it idempotent
to ease qdisc_tree_reduce_backlog() callers' life:
1. update_vf() decreases cl->cl_nactive, so we can check whether it is
non-zero before calling it.
2. eltree_remove() always removes RB node cl->el_node, but we can use
RB_EMPTY_NODE() + RB_CLEAR_NODE() to make it safe. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Do not double dequeue a configuration request
Some of our devices crash in tb_cfg_request_dequeue():
general protection fault, probably for non-canonical address 0xdead000000000122
CPU: 6 PID: 91007 Comm: kworker/6:2 Tainted: G U W 6.6.65
RIP: 0010:tb_cfg_request_dequeue+0x2d/0xa0
Call Trace:
<TASK>
? tb_cfg_request_dequeue+0x2d/0xa0
tb_cfg_request_work+0x33/0x80
worker_thread+0x386/0x8f0
kthread+0xed/0x110
ret_from_fork+0x38/0x50
ret_from_fork_asm+0x1b/0x30
The circumstances are unclear, however, the theory is that
tb_cfg_request_work() can be scheduled twice for a request:
first time via frame.callback from ring_work() and second
time from tb_cfg_request(). Both times kworkers will execute
tb_cfg_request_dequeue(), which results in double list_del()
from the ctl->request_queue (the list poison deference hints
at it: 0xdead000000000122).
Do not dequeue requests that don't have TB_CFG_REQUEST_ACTIVE
bit set. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: marvell/cesa - Handle zero-length skcipher requests
Do not access random memory for zero-length skcipher requests.
Just return 0. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: avoid using multiple devices with different type
For multiple devices, both primary and extra devices should be the
same type. `erofs_init_device` has already guaranteed that if the
primary is a file-backed device, extra devices should also be
regular files.
However, if the primary is a block device while the extra device
is a file-backed device, `erofs_init_device` will get an ENOTBLK,
which is not treated as an error in `erofs_fc_get_tree`, and that
leads to an UAF:
erofs_fc_get_tree
get_tree_bdev_flags(erofs_fc_fill_super)
erofs_read_superblock
erofs_init_device // sbi->dif0 is not inited yet,
// return -ENOTBLK
deactivate_locked_super
free(sbi)
if (err is -ENOTBLK)
sbi->dif0.file = filp_open() // sbi UAF
So if -ENOTBLK is hitted in `erofs_init_device`, it means the
primary device must be a block device, and the extra device
is not a block device. The error can be converted to -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64/fpsimd: Avoid clobbering kernel FPSIMD state with SMSTOP
On system with SME, a thread's kernel FPSIMD state may be erroneously
clobbered during a context switch immediately after that state is
restored. Systems without SME are unaffected.
If the CPU happens to be in streaming SVE mode before a context switch
to a thread with kernel FPSIMD state, fpsimd_thread_switch() will
restore the kernel FPSIMD state using fpsimd_load_kernel_state() while
the CPU is still in streaming SVE mode. When fpsimd_thread_switch()
subsequently calls fpsimd_flush_cpu_state(), this will execute an
SMSTOP, causing an exit from streaming SVE mode. The exit from
streaming SVE mode will cause the hardware to reset a number of
FPSIMD/SVE/SME registers, clobbering the FPSIMD state.
Fix this by calling fpsimd_flush_cpu_state() before restoring the kernel
FPSIMD state. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: arm-ni: Unregister PMUs on probe failure
When a resource allocation fails in one clock domain of an NI device,
we need to properly roll back all previously registered perf PMUs in
other clock domains of the same device.
Otherwise, it can lead to kernel panics.
Calling arm_ni_init+0x0/0xff8 [arm_ni] @ 2374
arm-ni ARMHCB70:00: Failed to request PMU region 0x1f3c13000
arm-ni ARMHCB70:00: probe with driver arm-ni failed with error -16
list_add corruption: next->prev should be prev (fffffd01e9698a18),
but was 0000000000000000. (next=ffff10001a0decc8).
pstate: 6340009 (nZCv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--)
pc : list_add_valid_or_report+0x7c/0xb8
lr : list_add_valid_or_report+0x7c/0xb8
Call trace:
__list_add_valid_or_report+0x7c/0xb8
perf_pmu_register+0x22c/0x3a0
arm_ni_probe+0x554/0x70c [arm_ni]
platform_probe+0x70/0xe8
really_probe+0xc6/0x4d8
driver_probe_device+0x48/0x170
__driver_attach+0x8e/0x1c0
bus_for_each_dev+0x64/0xf0
driver_add+0x138/0x260
bus_add_driver+0x68/0x138
__platform_driver_register+0x2c/0x40
arm_ni_init+0x14/0x2a [arm_ni]
do_init_module+0x36/0x298
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Oops - BUG: Fatal exception
SMP: stopping secondary CPUs |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fix ktls panic with sockmap
[ 2172.936997] ------------[ cut here ]------------
[ 2172.936999] kernel BUG at lib/iov_iter.c:629!
......
[ 2172.944996] PKRU: 55555554
[ 2172.945155] Call Trace:
[ 2172.945299] <TASK>
[ 2172.945428] ? die+0x36/0x90
[ 2172.945601] ? do_trap+0xdd/0x100
[ 2172.945795] ? iov_iter_revert+0x178/0x180
[ 2172.946031] ? iov_iter_revert+0x178/0x180
[ 2172.946267] ? do_error_trap+0x7d/0x110
[ 2172.946499] ? iov_iter_revert+0x178/0x180
[ 2172.946736] ? exc_invalid_op+0x50/0x70
[ 2172.946961] ? iov_iter_revert+0x178/0x180
[ 2172.947197] ? asm_exc_invalid_op+0x1a/0x20
[ 2172.947446] ? iov_iter_revert+0x178/0x180
[ 2172.947683] ? iov_iter_revert+0x5c/0x180
[ 2172.947913] tls_sw_sendmsg_locked.isra.0+0x794/0x840
[ 2172.948206] tls_sw_sendmsg+0x52/0x80
[ 2172.948420] ? inet_sendmsg+0x1f/0x70
[ 2172.948634] __sys_sendto+0x1cd/0x200
[ 2172.948848] ? find_held_lock+0x2b/0x80
[ 2172.949072] ? syscall_trace_enter+0x140/0x270
[ 2172.949330] ? __lock_release.isra.0+0x5e/0x170
[ 2172.949595] ? find_held_lock+0x2b/0x80
[ 2172.949817] ? syscall_trace_enter+0x140/0x270
[ 2172.950211] ? lockdep_hardirqs_on_prepare+0xda/0x190
[ 2172.950632] ? ktime_get_coarse_real_ts64+0xc2/0xd0
[ 2172.951036] __x64_sys_sendto+0x24/0x30
[ 2172.951382] do_syscall_64+0x90/0x170
......
After calling bpf_exec_tx_verdict(), the size of msg_pl->sg may increase,
e.g., when the BPF program executes bpf_msg_push_data().
If the BPF program sets cork_bytes and sg.size is smaller than cork_bytes,
it will return -ENOSPC and attempt to roll back to the non-zero copy
logic. However, during rollback, msg->msg_iter is reset, but since
msg_pl->sg.size has been increased, subsequent executions will exceed the
actual size of msg_iter.
'''
iov_iter_revert(&msg->msg_iter, msg_pl->sg.size - orig_size);
'''
The changes in this commit are based on the following considerations:
1. When cork_bytes is set, rolling back to non-zero copy logic is
pointless and can directly go to zero-copy logic.
2. We can not calculate the correct number of bytes to revert msg_iter.
Assume the original data is "abcdefgh" (8 bytes), and after 3 pushes
by the BPF program, it becomes 11-byte data: "abc?de?fgh?".
Then, we set cork_bytes to 6, which means the first 6 bytes have been
processed, and the remaining 5 bytes "?fgh?" will be cached until the
length meets the cork_bytes requirement.
However, some data in "?fgh?" is not within 'sg->msg_iter'
(but in msg_pl instead), especially the data "?" we pushed.
So it doesn't seem as simple as just reverting through an offset of
msg_iter.
3. For non-TLS sockets in tcp_bpf_sendmsg, when a "cork" situation occurs,
the user-space send() doesn't return an error, and the returned length is
the same as the input length parameter, even if some data is cached.
Additionally, I saw that the current non-zero-copy logic for handling
corking is written as:
'''
line 1177
else if (ret != -EAGAIN) {
if (ret == -ENOSPC)
ret = 0;
goto send_end;
'''
So it's ok to just return 'copied' without error when a "cork" situation
occurs. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Fix panic when calling skb_linearize
The panic can be reproduced by executing the command:
./bench sockmap -c 2 -p 1 -a --rx-verdict-ingress --rx-strp 100000
Then a kernel panic was captured:
'''
[ 657.460555] kernel BUG at net/core/skbuff.c:2178!
[ 657.462680] Tainted: [W]=WARN
[ 657.463287] Workqueue: events sk_psock_backlog
...
[ 657.469610] <TASK>
[ 657.469738] ? die+0x36/0x90
[ 657.469916] ? do_trap+0x1d0/0x270
[ 657.470118] ? pskb_expand_head+0x612/0xf40
[ 657.470376] ? pskb_expand_head+0x612/0xf40
[ 657.470620] ? do_error_trap+0xa3/0x170
[ 657.470846] ? pskb_expand_head+0x612/0xf40
[ 657.471092] ? handle_invalid_op+0x2c/0x40
[ 657.471335] ? pskb_expand_head+0x612/0xf40
[ 657.471579] ? exc_invalid_op+0x2d/0x40
[ 657.471805] ? asm_exc_invalid_op+0x1a/0x20
[ 657.472052] ? pskb_expand_head+0xd1/0xf40
[ 657.472292] ? pskb_expand_head+0x612/0xf40
[ 657.472540] ? lock_acquire+0x18f/0x4e0
[ 657.472766] ? find_held_lock+0x2d/0x110
[ 657.472999] ? __pfx_pskb_expand_head+0x10/0x10
[ 657.473263] ? __kmalloc_cache_noprof+0x5b/0x470
[ 657.473537] ? __pfx___lock_release.isra.0+0x10/0x10
[ 657.473826] __pskb_pull_tail+0xfd/0x1d20
[ 657.474062] ? __kasan_slab_alloc+0x4e/0x90
[ 657.474707] sk_psock_skb_ingress_enqueue+0x3bf/0x510
[ 657.475392] ? __kasan_kmalloc+0xaa/0xb0
[ 657.476010] sk_psock_backlog+0x5cf/0xd70
[ 657.476637] process_one_work+0x858/0x1a20
'''
The panic originates from the assertion BUG_ON(skb_shared(skb)) in
skb_linearize(). A previous commit(see Fixes tag) introduced skb_get()
to avoid race conditions between skb operations in the backlog and skb
release in the recvmsg path. However, this caused the panic to always
occur when skb_linearize is executed.
The "--rx-strp 100000" parameter forces the RX path to use the strparser
module which aggregates data until it reaches 100KB before calling sockmap
logic. The 100KB payload exceeds MAX_MSG_FRAGS, triggering skb_linearize.
To fix this issue, just move skb_get into sk_psock_skb_ingress_enqueue.
'''
sk_psock_backlog:
sk_psock_handle_skb
skb_get(skb) <== we move it into 'sk_psock_skb_ingress_enqueue'
sk_psock_skb_ingress____________
↓
|
| → sk_psock_skb_ingress_self
| sk_psock_skb_ingress_enqueue
sk_psock_verdict_apply_________________↑ skb_linearize
'''
Note that for verdict_apply path, the skb_get operation is unnecessary so
we add 'take_ref' param to control it's behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: zone: fix to avoid inconsistence in between SIT and SSA
w/ below testcase, it will cause inconsistence in between SIT and SSA.
create_null_blk 512 2 1024 1024
mkfs.f2fs -m /dev/nullb0
mount /dev/nullb0 /mnt/f2fs/
touch /mnt/f2fs/file
f2fs_io pinfile set /mnt/f2fs/file
fallocate -l 4GiB /mnt/f2fs/file
F2FS-fs (nullb0): Inconsistent segment (0) type [1, 0] in SSA and SIT
CPU: 5 UID: 0 PID: 2398 Comm: fallocate Tainted: G O 6.13.0-rc1 #84
Tainted: [O]=OOT_MODULE
Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
Call Trace:
<TASK>
dump_stack_lvl+0xb3/0xd0
dump_stack+0x14/0x20
f2fs_handle_critical_error+0x18c/0x220 [f2fs]
f2fs_stop_checkpoint+0x38/0x50 [f2fs]
do_garbage_collect+0x674/0x6e0 [f2fs]
f2fs_gc_range+0x12b/0x230 [f2fs]
f2fs_allocate_pinning_section+0x5c/0x150 [f2fs]
f2fs_expand_inode_data+0x1cc/0x3c0 [f2fs]
f2fs_fallocate+0x3c3/0x410 [f2fs]
vfs_fallocate+0x15f/0x4b0
__x64_sys_fallocate+0x4a/0x80
x64_sys_call+0x15e8/0x1b80
do_syscall_64+0x68/0x130
entry_SYSCALL_64_after_hwframe+0x67/0x6f
RIP: 0033:0x7f9dba5197ca
F2FS-fs (nullb0): Stopped filesystem due to reason: 4
The reason is f2fs_gc_range() may try to migrate block in curseg, however,
its SSA block is not uptodate due to the last summary block data is still
in cache of curseg.
In this patch, we add a condition in f2fs_gc_range() to check whether
section is opened or not, and skip block migration for opened section. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_set_pipapo: prevent overflow in lookup table allocation
When calculating the lookup table size, ensure the following
multiplication does not overflow:
- desc->field_len[] maximum value is U8_MAX multiplied by
NFT_PIPAPO_GROUPS_PER_BYTE(f) that can be 2, worst case.
- NFT_PIPAPO_BUCKETS(f->bb) is 2^8, worst case.
- sizeof(unsigned long), from sizeof(*f->lt), lt in
struct nft_pipapo_field.
Then, use check_mul_overflow() to multiply by bucket size and then use
check_add_overflow() to the alignment for avx2 (if needed). Finally, add
lt_size_check_overflow() helper and use it to consolidate this.
While at it, replace leftover allocation using the GFP_KERNEL to
GFP_KERNEL_ACCOUNT for consistency, in pipapo_resize(). |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix error flow upon firmware failure for RQ destruction
Upon RQ destruction if the firmware command fails which is the
last resource to be destroyed some SW resources were already cleaned
regardless of the failure.
Now properly rollback the object to its original state upon such failure.
In order to avoid a use-after free in case someone tries to destroy the
object again, which results in the following kernel trace:
refcount_t: underflow; use-after-free.
WARNING: CPU: 0 PID: 37589 at lib/refcount.c:28 refcount_warn_saturate+0xf4/0x148
Modules linked in: rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) mlx5_ib(OE) rfkill mlx5_core(OE) mlxdevm(OE) ib_uverbs(OE) ib_core(OE) psample mlxfw(OE) mlx_compat(OE) macsec tls pci_hyperv_intf sunrpc vfat fat virtio_net net_failover failover fuse loop nfnetlink vsock_loopback vmw_vsock_virtio_transport_common vmw_vsock_vmci_transport vmw_vmci vsock xfs crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce virtio_console virtio_gpu virtio_blk virtio_dma_buf virtio_mmio dm_mirror dm_region_hash dm_log dm_mod xpmem(OE)
CPU: 0 UID: 0 PID: 37589 Comm: python3 Kdump: loaded Tainted: G OE ------- --- 6.12.0-54.el10.aarch64 #1
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : refcount_warn_saturate+0xf4/0x148
lr : refcount_warn_saturate+0xf4/0x148
sp : ffff80008b81b7e0
x29: ffff80008b81b7e0 x28: ffff000133d51600 x27: 0000000000000001
x26: 0000000000000000 x25: 00000000ffffffea x24: ffff00010ae80f00
x23: ffff00010ae80f80 x22: ffff0000c66e5d08 x21: 0000000000000000
x20: ffff0000c66e0000 x19: ffff00010ae80340 x18: 0000000000000006
x17: 0000000000000000 x16: 0000000000000020 x15: ffff80008b81b37f
x14: 0000000000000000 x13: 2e656572662d7265 x12: ffff80008283ef78
x11: ffff80008257efd0 x10: ffff80008283efd0 x9 : ffff80008021ed90
x8 : 0000000000000001 x7 : 00000000000bffe8 x6 : c0000000ffff7fff
x5 : ffff0001fb8e3408 x4 : 0000000000000000 x3 : ffff800179993000
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000133d51600
Call trace:
refcount_warn_saturate+0xf4/0x148
mlx5_core_put_rsc+0x88/0xa0 [mlx5_ib]
mlx5_core_destroy_rq_tracked+0x64/0x98 [mlx5_ib]
mlx5_ib_destroy_wq+0x34/0x80 [mlx5_ib]
ib_destroy_wq_user+0x30/0xc0 [ib_core]
uverbs_free_wq+0x28/0x58 [ib_uverbs]
destroy_hw_idr_uobject+0x34/0x78 [ib_uverbs]
uverbs_destroy_uobject+0x48/0x240 [ib_uverbs]
__uverbs_cleanup_ufile+0xd4/0x1a8 [ib_uverbs]
uverbs_destroy_ufile_hw+0x48/0x120 [ib_uverbs]
ib_uverbs_close+0x2c/0x100 [ib_uverbs]
__fput+0xd8/0x2f0
__fput_sync+0x50/0x70
__arm64_sys_close+0x40/0x90
invoke_syscall.constprop.0+0x74/0xd0
do_el0_svc+0x48/0xe8
el0_svc+0x44/0x1d0
el0t_64_sync_handler+0x120/0x130
el0t_64_sync+0x1a4/0x1a8 |
| In the Linux kernel, the following vulnerability has been resolved:
af_packet: move notifier's packet_dev_mc out of rcu critical section
Syzkaller reports the following issue:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:578
__mutex_lock+0x106/0xe80 kernel/locking/mutex.c:746
team_change_rx_flags+0x38/0x220 drivers/net/team/team_core.c:1781
dev_change_rx_flags net/core/dev.c:9145 [inline]
__dev_set_promiscuity+0x3f8/0x590 net/core/dev.c:9189
netif_set_promiscuity+0x50/0xe0 net/core/dev.c:9201
dev_set_promiscuity+0x126/0x260 net/core/dev_api.c:286 packet_dev_mc net/packet/af_packet.c:3698 [inline]
packet_dev_mclist_delete net/packet/af_packet.c:3722 [inline]
packet_notifier+0x292/0xa60 net/packet/af_packet.c:4247
notifier_call_chain+0x1b3/0x3e0 kernel/notifier.c:85
call_netdevice_notifiers_extack net/core/dev.c:2214 [inline]
call_netdevice_notifiers net/core/dev.c:2228 [inline]
unregister_netdevice_many_notify+0x15d8/0x2330 net/core/dev.c:11972
rtnl_delete_link net/core/rtnetlink.c:3522 [inline]
rtnl_dellink+0x488/0x710 net/core/rtnetlink.c:3564
rtnetlink_rcv_msg+0x7cf/0xb70 net/core/rtnetlink.c:6955
netlink_rcv_skb+0x219/0x490 net/netlink/af_netlink.c:2534
Calling `PACKET_ADD_MEMBERSHIP` on an ops-locked device can trigger
the `NETDEV_UNREGISTER` notifier, which may require disabling promiscuous
and/or allmulti mode. Both of these operations require acquiring
the netdev instance lock.
Move the call to `packet_dev_mc` outside of the RCU critical section.
The `mclist` modifications (add, del, flush, unregister) are protected by
the RTNL, not the RCU. The RCU only protects the `sklist` and its
associated `sks`. The delayed operation on the `mclist` entry remains
within the RTNL. |
