| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
phy: renesas: rcar-gen2: Fix double of_node_put on phy creation failure
for_each_child_of_node_scoped() releases the node reference on scope
exit, so the explicit of_node_put(np) in the devm_phy_create() error
path drops it twice.
Drop the redundant of_node_put() and let the scoped cleanup handle it. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: sunplus: fix error handling in sp_uphy_init()
Fix the error paths of sp_uphy_init() to undo exactly what each stage
did: return directly if clk_prepare_enable() fails, release only the clock
if reset_control_deassert() fails, and jump to err_reset if
update_disc_vol() fails so the clock and reset are not leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx6: Use PFP on the compute queues too
On GFX6, the compute rings use the same CP path as
the graphics ring. The only difference is that they
don't support draw commands. (As opposed to GFX7 and
newer which have a separate command parser that is
called MEC for compute queues.)
This means that we have to take into consideration
that the PFP also exists on compute queues on GFX6:
Use PFP for register writes on both graphics and
compute queues.
In the pipeline sync, use the PFP to wait for the
previous fence (and not the ME) to prevent the PFP
from starting to execute the next submission while
the ME is still in the previous submission.
After a VM flush, emit PFP_SYNC_ME on compute
queues as well. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Remove redundant VPD flash read in sysfs read path
qla2x00_sysfs_read_vpd() called ha->isp_ops->read_optrom() a second time
after releasing optrom_mutex. The repeated read is redundant and, unlike
the first, runs without optrom_mutex held, exposing flash access to
concurrent optrom operations. Drop the duplicate call. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware_loader: do not queue completed sysfs fallback requests
fw_load_sysfs_fallback() calls device_add() before adding the fw_priv to
pending_fw_head. device_add() publishes the fallback loading interface, so
a userspace helper which discovers the device by scanning sysfs can write 0
to the loading attribute and complete the request before it is queued as
pending.
In that interleaving firmware_loading_store() calls fw_state_done() while
pending_list still points to itself, so it cannot remove an entry from
pending_fw_head. The subsequent unconditional list_add() then queues an
already-completed fw_priv. Once the request is released, pending_fw_head
can retain a pointer to freed memory and the next fallback request can
fault while validating the list.
Only in-flight fallback requests need suspend or reboot abort handling. If
the request is already DONE after device_add(), return success from the
fallback path without sending another uevent, waiting again, or queueing it
as pending. This preserves the invariant that pending_fw_head contains only
active fallback requests. |
| In the Linux kernel, the following vulnerability has been resolved:
hugetlbfs: release subpool on fill_super failure
hugetlbfs_fill_super() allocates a hugepage subpool when size or min_size
mount options are specified. hugepage_new_subpool() may also reserve huge
pages for min_size.
If root dentry creation fails after the subpool is created, the failure
path frees the subpool with kfree(). This bypasses hugepage_put_subpool()
and can leave min_size reservations charged.
Use hugepage_put_subpool() on the failure path, matching the normal
put_super path. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: qmp-usb-legacy: Fix possible NULL-deref on early runtime suspend
There is a small window where the runtime suspend callback may run
after pm_runtime_enable() and before pm_runtime_forbid(). In this
case, a crash occurs because runtime suspend/resume dereferences
qmp->phy pointer, which is not yet initialized:
`if (!qmp->phy->init_count) {`
This can also happen if user re-enables runtime-pm via the sysfs
attribute before qmp phy is initialized.
Similarly to other qcom phy drivers, introduce a qmp->phy_initialized
variable that can be used to avoid relying on the possibly uninitialized
phy pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: snps-femto-v2: Fix possible NULL-deref on early runtime suspend
Runtime PM must be enabled before creating the PHY, since phy_create()
only enables runtime PM on the PHY device if it is already enabled on
this parent device. However, the runtime PM callbacks dereference the
hsphy instance, which is not yet ready, leaving a window where a suspend
callback may trigger a NULL pointer dereference.
Take a runtime PM usage reference with pm_runtime_get_noresume() before
enabling runtime PM and release it once the PHY has been created, so that
no runtime suspend can run before the PHY is ready. This also prevents a
short window where an unnecessary runtime suspend can occur.
Use the devres-managed version to ensure PM runtime is symmetrically
disabled during driver removal for proper cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: qmp-usb: Fix possible NULL-deref on early runtime suspend
There is a small window where the runtime suspend callback may run
after pm_runtime_enable() and before pm_runtime_forbid(). In this
case, a crash occurs because runtime suspend/resume dereferences
qmp->phy pointer, which is not yet initialized:
`if (!qmp->phy->init_count) {`
This can also happen if user re-enables runtime-pm via the sysfs
attribute before qmp phy is initialized.
Similarly to other qcom phy drivers, introduce a qmp->phy_initialized
variable that can be used to avoid relying on the possibly uninitialized
phy pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5: round bitmap stripes with sector division
raid5_bitmap_sector_map() aligns the array range to full RAID5 stripe
widths before converting it to component sectors. That width is
chunk_sectors multiplied by the number of data disks, and it is not
always a power of two.
Reproduce with a 4-disk RAID5, 1024-sector chunks, and three data disks.
The full-stripe width is 3072 sectors. For a one-sector write at array
sector 3072, correct rounding gives array range [3072, 6144), which maps
to component range [1024, 2048). The old round_down()/round_up() logic
instead gives [1024, 4096), which maps to [0, 1024).
Use sector_div() based arithmetic so the rounded range is aligned to the
actual RAID5 stripe width.
The deterministic mapper test now reports the fixed component range as
[1024, 2048), while the old mask-based range was [0, 1024). |
| In the Linux kernel, the following vulnerability has been resolved:
md: wait for behind writes before destroying bitmap
__md_stop() destroyed the bitmap before calling mddev_detach(). That made
mddev_detach() skip bitmap_ops->wait_behind_writes(), because the bitmap
was already disconnected from mddev.
This was still safe for the legacy bitmap because bitmap_destroy() waits
for behind writes itself. llbitmap keeps that wait in its
->wait_behind_writes() operation instead, while ->destroy() tears down the
llbitmap storage. With the old ordering, RAID1 behind-write completions
could still run after llbitmap storage had been freed.
Call mddev_detach() before md_bitmap_destroy() so the common detach path
can wait for behind writes while the bitmap is still alive. Only destroy
the bitmap after those users are gone. |
| In the Linux kernel, the following vulnerability has been resolved:
md/md-llbitmap: prevent create failure bitmap UAF
llbitmap_create() publishes mddev->bitmap before reading the bitmap
superblock. This is needed because llbitmap_read_sb() can initialize a
new bitmap and flush it through helpers that use mddev->bitmap.
If llbitmap_read_sb() fails, the old cleanup dropped bitmap_info.mutex
and freed llbitmap before clearing mddev->bitmap. Readers such as
/proc/mdstat rely on bitmap_info.mutex to keep the bitmap pointer stable
while collecting bitmap stats, so they could observe the stale pointer
after the failed create path released the mutex.
Clear mddev->bitmap while still holding bitmap_info.mutex, then free the
failed llbitmap after dropping the mutex. This makes mutex-protected
readers see either a live bitmap or no bitmap. |
| In the Linux kernel, the following vulnerability has been resolved:
md/md-llbitmap: stop daemon timer rearm on destroy
llbitmap_destroy() deletes pending_timer before flushing
md_llbitmap_io_wq. However, daemon_work can still be queued or running
after the timer has been deleted, and the daemon path can arm
pending_timer again when it finds dirty chunks that are not ready to
flush yet.
If that happens during teardown, pending_timer can remain armed after
llbitmap is freed and later dereference freed memory.
Add a BITMAP_SHUTDOWN bit to llbitmap->flags, set it before deleting
the timer, and make the timer and daemon paths stop queueing or rearming
work once teardown starts. Cancel daemon_work before flushing the shared
workqueue so no already queued daemon instance can race with the free.
Use timer_shutdown_sync() so a daemon instance that passed the shutdown
check before teardown cannot rearm the timer afterward.
BITMAP_SHUTDOWN is a runtime-only state. Mask it out when reading and
updating the llbitmap superblock so the shutdown state is never loaded
from disk or persisted to disk. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: don't set array_frozen in raid1_takeover()
raid1_takeover() sets conf->array_frozen = 1 on the newly-allocated
r1conf and nothing ever clears it, so every I/O to the array stalls
permanently once _wait_barrier() sees it stuck at 1.
This used to be harmless: level_store() called mddev_resume() right
after pers->run(), which called raid1_quiesce(mddev, 0) and cleared
array_frozen back to 0 regardless of what raid1_takeover() set. Commit
b39f35ebe86d ("md: don't quiesce in mddev_suspend()") removed that
quiesce(mddev, 0) call, so the pre-set now sticks.
setup_conf() already zero-initializes the new r1conf via kzalloc, so
just don't set array_frozen here.
Same class of bug as commit 892da88d1cd9 ("md/raid10: fix a
'conf->barrier' leakage in raid10_takeover()"), also triggered by
b39f35ebe86d. |
| In the Linux kernel, the following vulnerability has been resolved:
coresight: etm4x: fix underflow for usage of (nrseqstate - 1)
According to IHI006H Embedded Trace Macrocell Architecture
Specification[0], TRCSEQEVR<n> is implemented only when
TRCIDR5.NUMSEQSTATE is 0b100, in which case n ranges from 0 to 2;
otherwise, TRCIDR5.NUMSEQSTATE is 0b000.
IOW, the number of usage in the initialisation or setting
TRCSEQEVR<n> with drvdata->nrseqstate - 1 in the loop could make
underflow issue when TRCIDR5.NUMSEQSTATE is 0b000.
Therefore, introduce nr_seq_ctrls field and untie it from nrseqstate.
As part of this introduce ETM_MAX_SEQ_TRANSITIONS macro and
apply nr_seq_ctrls and above macro to TRCSEQEVR<n> relevant fields setup. |
| In the Linux kernel, the following vulnerability has been resolved:
coresight: etm4x: missing cscfg_csdev_disable_active_config() in perf enable
In the perf enable path, there are missing cases where
cscfg_csdev_disable_active_config() is not called:
- Branch broadcast is selected but not supported by the hardware
- etm4_enable_hw() fails
This can lead to a leak of config_desc->active_cnt.
Fix this by properly calling cscfg_csdev_disable_active_config()
in these error paths. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: arm_pmuv3: Zero initialize hw_id branch stack field
PERF_SAMPLE_BRANCH_HW_INDEX is supported by BRBE so hw_id is passed to
userspace, but it's never set by the BRBE driver. Zero initialize it as
it should be according to the docs:
* For the architectures whose raw branch records are
* already stored in age order, the hw_idx should be 0.
It's probably too risky to remove PERF_SAMPLE_BRANCH_HW_INDEX from BRBE
now in case anyone is setting it and reading the value, but zero
initializing the whole struct also protects against the same issue with
new fields that are added in the future. |
| In the Linux kernel, the following vulnerability has been resolved:
arm_mpam: Fix a NULL pointer dereference on unbinding after an error interrupt
If a user unbinds an MSC after mpam_disable() has been run in response
to an error interrupt then a dereference of a NULL pointer occurs as
mpam_disable() sets the drvdata to NULL. Add an early return to the driver
remove callback to avoid this. |
| In the Linux kernel, the following vulnerability has been resolved:
arm_mpam: Disable driver unbind to avoid UAF
When a user unbinds an MSC and that MSC is the only MSC left for a
component then the corresponding mpam_component will be freed. If the user
then goes on to read the schemata file in the resctrl filesystem then the
mpam_component will be accessed from resctrl_arch_get_config() leading to a
use after free.
As the MPAM driver is not a module the unbind sysfs interface is the only
way to trigger the remove. Instead of dealing with the complexity of
allowing some unused MSC to unbind just remove the unbind sysfs interface. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject load-acquire from pointers requiring fault protection
A BPF_LOAD_ACQ is not rewritten to a BPF_PROBE_MEM load by the verifier,
unlike a regular BPF_LDX, so the JIT emits a plain load with no exception
table entry and a fault panics the kernel instead of being handled.
Reject the source pointer types that a BPF_LDX would have had that fault
protection applied to, i.e. the ones bpf_convert_ctx_accesses() turns
into BPF_PROBE_MEM: a bare PTR_TO_BTF_ID, PTR_TO_BTF_ID | PTR_UNTRUSTED,
PTR_TO_BTF_ID | MEM_ALLOC | PTR_UNTRUSTED and PTR_TO_MEM | MEM_RDONLY |
PTR_UNTRUSTED.
This is reachable e.g. by loading ->mm out of a trusted task_struct
yields an untrusted pointer to mm_struct, and it is NULL for a kernel
thread:
[...]
SEC("tp_btf/sched_switch")
int BPF_PROG(demo, bool preempt, struct task_struct *prev,
struct task_struct *next)
{
struct mm_struct *mm = next->mm; /* untrusted */
out_ldx = (__u64)mm->pgd; /* BPF_LDX */
out_acq = load_acquire(&mm->pgd); /* BPF_LOAD_ACQ */
return 0;
}
[...]
Both dereference the same pointer, but only the BPF_LDX is protected
(x86-64 JIT, jump targets shown prog-relative):
[...]
; out_ldx = (__u64)mm->pgd;
17: movq $-10485760, %r10
1e: movq %rsi, %r11
21: addq $184, %r11
28: subq %r10, %r11
2b: movabsq $140737498841088, %r10
35: cmpq %r10, %r11
38: ja 0x3e <-- kernel addr?
3a: xorl %edi, %edi <-- no: dst = 0, skip the load
3c: jmp 0x45
3e: movq 184(%rsi), %rdi <-- yes: load + extable entry
[...]
; load_acquire(&mm->pgd)
53: movq %rsi, %rdi
56: movq 184(%rdi), %rax <-- no check, no extable entry
[...]
Note that BPF_PROBE_MEM is not visible in a bpftool xlated dump, as
bpf_insn_prepare_dump() rewrites it back to BPF_MEM.
A PTR_TRUSTED pointer is deliberately not on the list. Such a load is
not converted either, but it does not need to be, since the pointer is
guaranteed live, so load-acquire from it stays allowed.
The check is gated on BPF_LOAD_ACQ so that atomic RMW and store-release
error messages are unchanged; writes (RMW / store-release) to such
pointers are already rejected elsewhere, so only load-acquire needs this. |
