| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Cap MSIX used to online CPUs + 1
The irdma driver can use a maximum number of msix vectors equal
to num_online_cpus() + 1 and the kernel warning stack below is shown
if that number is exceeded.
The kernel throws a warning as the driver tries to update the affinity
hint with a CPU mask greater than the max CPU IDs. Fix this by capping
the MSIX vectors to num_online_cpus() + 1.
WARNING: CPU: 7 PID: 23655 at include/linux/cpumask.h:106 irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
RIP: 0010:irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
Call Trace:
irdma_rt_init_hw+0xa62/0x1290 [irdma]
? irdma_alloc_local_mac_entry+0x1a0/0x1a0 [irdma]
? __is_kernel_percpu_address+0x63/0x310
? rcu_read_lock_held_common+0xe/0xb0
? irdma_lan_unregister_qset+0x280/0x280 [irdma]
? irdma_request_reset+0x80/0x80 [irdma]
? ice_get_qos_params+0x84/0x390 [ice]
irdma_probe+0xa40/0xfc0 [irdma]
? rcu_read_lock_bh_held+0xd0/0xd0
? irdma_remove+0x140/0x140 [irdma]
? rcu_read_lock_sched_held+0x62/0xe0
? down_write+0x187/0x3d0
? auxiliary_match_id+0xf0/0x1a0
? irdma_remove+0x140/0x140 [irdma]
auxiliary_bus_probe+0xa6/0x100
__driver_probe_device+0x4a4/0xd50
? __device_attach_driver+0x2c0/0x2c0
driver_probe_device+0x4a/0x110
__driver_attach+0x1aa/0x350
bus_for_each_dev+0x11d/0x1b0
? subsys_dev_iter_init+0xe0/0xe0
bus_add_driver+0x3b1/0x610
driver_register+0x18e/0x410
? 0xffffffffc0b88000
irdma_init_module+0x50/0xaa [irdma]
do_one_initcall+0x103/0x5f0
? perf_trace_initcall_level+0x420/0x420
? do_init_module+0x4e/0x700
? __kasan_kmalloc+0x7d/0xa0
? kmem_cache_alloc_trace+0x188/0x2b0
? kasan_unpoison+0x21/0x50
do_init_module+0x1d1/0x700
load_module+0x3867/0x5260
? layout_and_allocate+0x3990/0x3990
? rcu_read_lock_held_common+0xe/0xb0
? rcu_read_lock_sched_held+0x62/0xe0
? rcu_read_lock_bh_held+0xd0/0xd0
? __vmalloc_node_range+0x46b/0x890
? lock_release+0x5c8/0xba0
? alloc_vm_area+0x120/0x120
? selinux_kernel_module_from_file+0x2a5/0x300
? __inode_security_revalidate+0xf0/0xf0
? __do_sys_init_module+0x1db/0x260
__do_sys_init_module+0x1db/0x260
? load_module+0x5260/0x5260
? do_syscall_64+0x22/0x450
do_syscall_64+0xa5/0x450
entry_SYSCALL_64_after_hwframe+0x66/0xdb |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix rbtree traversal bug in ext4_mb_use_preallocated
During allocations, while looking for preallocations(PA) in the per
inode rbtree, we can't do a direct traversal of the tree because
ext4_mb_discard_group_preallocation() can paralelly mark the pa deleted
and that can cause direct traversal to skip some entries. This was
leading to a BUG_ON() being hit [1] when we missed a PA that could satisfy
our request and ultimately tried to create a new PA that would overlap
with the missed one.
To makes sure we handle that case while still keeping the performance of
the rbtree, we make use of the fact that the only pa that could possibly
overlap the original goal start is the one that satisfies the below
conditions:
1. It must have it's logical start immediately to the left of
(ie less than) original logical start.
2. It must not be deleted
To find this pa we use the following traversal method:
1. Descend into the rbtree normally to find the immediate neighboring
PA. Here we keep descending irrespective of if the PA is deleted or if
it overlaps with our request etc. The goal is to find an immediately
adjacent PA.
2. If the found PA is on right of original goal, use rb_prev() to find
the left adjacent PA.
3. Check if this PA is deleted and keep moving left with rb_prev() until
a non deleted PA is found.
4. This is the PA we are looking for. Now we can check if it can satisfy
the original request and proceed accordingly.
This approach also takes care of having deleted PAs in the tree.
(While we are at it, also fix a possible overflow bug in calculating the
end of a PA)
[1] https://lore.kernel.org/linux-ext4/CA+G9fYv2FRpLqBZf34ZinR8bU2_ZRAUOjKAD3+tKRFaEQHtt8Q@mail.gmail.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
posix-timers: Prevent RT livelock in itimer_delete()
itimer_delete() has a retry loop when the timer is concurrently expired. On
non-RT kernels this just spin-waits until the timer callback has completed,
except for posix CPU timers which have HAVE_POSIX_CPU_TIMERS_TASK_WORK
enabled.
In that case and on RT kernels the existing task could live lock when
preempting the task which does the timer delivery.
Replace spin_unlock() with an invocation of timer_wait_running() to handle
it the same way as the other retry loops in the posix timer code. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: Ignore frags from uninitialized peer in dp.
When max virtual ap interfaces are configured in all the bands with
ACS and hostapd restart is done every 60s, a crash is observed at
random times.
In this certain scenario, a fragmented packet is received for
self peer, for which rx_tid and rx_frags are not initialized in
datapath. While handling this fragment, crash is observed as the
rx_frag list is uninitialised and when we walk in
ath11k_dp_rx_h_sort_frags, skb null leads to exception.
To address this, before processing received fragments we check
dp_setup_done flag is set to ensure that peer has completed its
dp peer setup for fragment queue, else ignore processing the
fragments.
Call trace:
ath11k_dp_process_rx_err+0x550/0x1084 [ath11k]
ath11k_dp_service_srng+0x70/0x370 [ath11k]
0xffffffc009693a04
__napi_poll+0x30/0xa4
net_rx_action+0x118/0x270
__do_softirq+0x10c/0x244
irq_exit+0x64/0xb4
__handle_domain_irq+0x88/0xac
gic_handle_irq+0x74/0xbc
el1_irq+0xf0/0x1c0
arch_cpu_idle+0x10/0x18
do_idle+0x104/0x248
cpu_startup_entry+0x20/0x64
rest_init+0xd0/0xdc
arch_call_rest_init+0xc/0x14
start_kernel+0x480/0x4b8
Code: f9400281 f94066a2 91405021 b94a0023 (f9406401)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
block/rq_qos: protect rq_qos apis with a new lock
commit 50e34d78815e ("block: disable the elevator int del_gendisk")
move rq_qos_exit() from disk_release() to del_gendisk(), this will
introduce some problems:
1) If rq_qos_add() is triggered by enabling iocost/iolatency through
cgroupfs, then it can concurrent with del_gendisk(), it's not safe to
write 'q->rq_qos' concurrently.
2) Activate cgroup policy that is relied on rq_qos will call
rq_qos_add() and blkcg_activate_policy(), and if rq_qos_exit() is
called in the middle, null-ptr-dereference will be triggered in
blkcg_activate_policy().
3) blkg_conf_open_bdev() can call blkdev_get_no_open() first to find the
disk, then if rq_qos_exit() from del_gendisk() is done before
rq_qos_add(), then memory will be leaked.
This patch add a new disk level mutex 'rq_qos_mutex':
1) The lock will protect rq_qos_exit() directly.
2) For wbt that doesn't relied on blk-cgroup, rq_qos_add() can only be
called from disk initialization for now because wbt can't be
destructed until rq_qos_exit(), so it's safe not to protect wbt for
now. Hoever, in case that rq_qos dynamically destruction is supported
in the furture, this patch also protect rq_qos_add() from wbt_init()
directly, this is enough because blk-sysfs already synchronize
writers with disk removal.
3) For iocost and iolatency, in order to synchronize disk removal and
cgroup configuration, the lock is held after blkdev_get_no_open()
from blkg_conf_open_bdev(), and is released in blkg_conf_exit().
In order to fix the above memory leak, disk_live() is checked after
holding the new lock. |
| In the Linux kernel, the following vulnerability has been resolved:
kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
syzkaller found a memory leak in kcm_sendmsg(), and commit c821a88bd720
("kcm: Fix memory leak in error path of kcm_sendmsg()") suppressed it by
updating kcm_tx_msg(head)->last_skb if partial data is copied so that the
following sendmsg() will resume from the skb.
However, we cannot know how many bytes were copied when we get the error.
Thus, we could mess up the MSG_MORE queue.
When kcm_sendmsg() fails for SOCK_DGRAM, we should purge the queue as we
do so for UDP by udp_flush_pending_frames().
Even without this change, when the error occurred, the following sendmsg()
resumed from a wrong skb and the queue was messed up. However, we have
yet to get such a report, and only syzkaller stumbled on it. So, this
can be changed safely.
Note this does not change SOCK_SEQPACKET behaviour. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Avoid use-after-free in dbg for hci_add_adv_monitor()
KSAN reports use-after-free in hci_add_adv_monitor().
While adding an adv monitor,
hci_add_adv_monitor() calls ->
msft_add_monitor_pattern() calls ->
msft_add_monitor_sync() calls ->
msft_le_monitor_advertisement_cb() calls in an error case ->
hci_free_adv_monitor() which frees the *moniter.
This is referenced by bt_dev_dbg() in hci_add_adv_monitor().
Fix the bt_dev_dbg() by using handle instead of monitor->handle. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: fix null-ptr-deref in raid10_sync_request
init_resync() inits mempool and sets conf->have_replacemnt at the beginning
of sync, close_sync() frees the mempool when sync is completed.
After [1] recovery might be skipped and init_resync() is called but
close_sync() is not. null-ptr-deref occurs with r10bio->dev[i].repl_bio.
The following is one way to reproduce the issue.
1) create a array, wait for resync to complete, mddev->recovery_cp is set
to MaxSector.
2) recovery is woken and it is skipped. conf->have_replacement is set to
0 in init_resync(). close_sync() not called.
3) some io errors and rdev A is set to WantReplacement.
4) a new device is added and set to A's replacement.
5) recovery is woken, A have replacement, but conf->have_replacemnt is
0. r10bio->dev[i].repl_bio will not be alloced and null-ptr-deref
occurs.
Fix it by not calling init_resync() if recovery skipped.
[1] commit 7e83ccbecd60 ("md/raid10: Allow skipping recovery when clean arrays are assembled") |
| In the Linux kernel, the following vulnerability has been resolved:
usb: early: xhci-dbc: Fix a potential out-of-bound memory access
If xdbc_bulk_write() fails, the values in 'buf' can be anything. So the
string is not guaranteed to be NULL terminated when xdbc_trace() is called.
Reserve an extra byte, which will be zeroed automatically because 'buf' is
a static variable, in order to avoid troubles, should it happen. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: wcd-mbhc-v2: fix resource leaks on component remove
The MBHC resources must be released on component probe failure and
removal so can not be tied to the lifetime of the component device.
This is specifically needed to allow probe deferrals of the sound card
which otherwise fails when reprobing the codec component:
snd-sc8280xp sound: ASoC: failed to instantiate card -517
genirq: Flags mismatch irq 299. 00002001 (mbhc sw intr) vs. 00002001 (mbhc sw intr)
wcd938x_codec audio-codec: Failed to request mbhc interrupts -16
wcd938x_codec audio-codec: mbhc initialization failed
wcd938x_codec audio-codec: ASoC: error at snd_soc_component_probe on audio-codec: -16
snd-sc8280xp sound: ASoC: failed to instantiate card -16 |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix infinite loop in nilfs_mdt_get_block()
If the disk image that nilfs2 mounts is corrupted and a virtual block
address obtained by block lookup for a metadata file is invalid,
nilfs_bmap_lookup_at_level() may return the same internal return code as
-ENOENT, meaning the block does not exist in the metadata file.
This duplication of return codes confuses nilfs_mdt_get_block(), causing
it to read and create a metadata block indefinitely.
In particular, if this happens to the inode metadata file, ifile,
semaphore i_rwsem can be left held, causing task hangs in lock_mount.
Fix this issue by making nilfs_bmap_lookup_at_level() treat virtual block
address translation failures with -ENOENT as metadata corruption instead
of returning the error code. |
| In the Linux kernel, the following vulnerability has been resolved:
usb-storage: alauda: Fix uninit-value in alauda_check_media()
Syzbot got KMSAN to complain about access to an uninitialized value in
the alauda subdriver of usb-storage:
BUG: KMSAN: uninit-value in alauda_transport+0x462/0x57f0
drivers/usb/storage/alauda.c:1137
CPU: 0 PID: 12279 Comm: usb-storage Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
__msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
alauda_check_media+0x344/0x3310 drivers/usb/storage/alauda.c:460
The problem is that alauda_check_media() doesn't verify that its USB
transfer succeeded before trying to use the received data. What
should happen if the transfer fails isn't entirely clear, but a
reasonably conservative approach is to pretend that no media is
present.
A similar problem exists in a usb_stor_dbg() call in
alauda_get_media_status(). In this case, when an error occurs the
call is redundant, because usb_stor_ctrl_transfer() already will print
a debugging message.
Finally, unrelated to the uninitialized memory access, is the fact
that alauda_check_media() performs DMA to a buffer on the stack.
Fortunately usb-storage provides a general purpose DMA-able buffer for
uses like this. We'll use it instead. |
| In the Linux kernel, the following vulnerability has been resolved:
iavf: use internal state to free traffic IRQs
If the system tries to close the netdev while iavf_reset_task() is
running, __LINK_STATE_START will be cleared and netif_running() will
return false in iavf_reinit_interrupt_scheme(). This will result in
iavf_free_traffic_irqs() not being called and a leak as follows:
[7632.489326] remove_proc_entry: removing non-empty directory 'irq/999', leaking at least 'iavf-enp24s0f0v0-TxRx-0'
[7632.490214] WARNING: CPU: 0 PID: 10 at fs/proc/generic.c:718 remove_proc_entry+0x19b/0x1b0
is shown when pci_disable_msix() is later called. Fix by using the
internal adapter state. The traffic IRQs will always exist if
state == __IAVF_RUNNING. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dp: Drop aux devices together with DP controller
Using devres to depopulate the aux bus made sure that upon a probe
deferral the EDP panel device would be destroyed and recreated upon next
attempt.
But the struct device which the devres is tied to is the DPUs
(drm_dev->dev), which may be happen after the DP controller is torn
down.
Indications of this can be seen in the commonly seen EDID-hexdump full
of zeros in the log, or the occasional/rare KASAN fault where the
panel's attempt to read the EDID information causes a use after free on
DP resources.
It's tempting to move the devres to the DP controller's struct device,
but the resources used by the device(s) on the aux bus are explicitly
torn down in the error path. The KASAN-reported use-after-free also
remains, as the DP aux "module" explicitly frees its devres-allocated
memory in this code path.
As such, explicitly depopulate the aux bus in the error path, and in the
component unbind path, to avoid these issues.
Patchwork: https://patchwork.freedesktop.org/patch/542163/ |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: mediatek: mt8186: Fix use-after-free in driver remove path
When devm runs function in the "remove" path for a device it runs them
in the reverse order. That means that if you have parts of your driver
that aren't using devm or are using "roll your own" devm w/
devm_add_action_or_reset() you need to keep that in mind.
The mt8186 audio driver didn't quite get this right. Specifically, in
mt8186_init_clock() it called mt8186_audsys_clk_register() and then
went on to call a bunch of other devm function. The caller of
mt8186_init_clock() used devm_add_action_or_reset() to call
mt8186_deinit_clock() but, because of the intervening devm functions,
the order was wrong.
Specifically at probe time, the order was:
1. mt8186_audsys_clk_register()
2. afe_priv->clk = devm_kcalloc(...)
3. afe_priv->clk[i] = devm_clk_get(...)
At remove time, the order (which should have been 3, 2, 1) was:
1. mt8186_audsys_clk_unregister()
3. Free all of afe_priv->clk[i]
2. Free afe_priv->clk
The above seemed to be causing a use-after-free. Luckily, it's easy to
fix this by simply using devm more correctly. Let's move the
devm_add_action_or_reset() to the right place. In addition to fixing
the use-after-free, code inspection shows that this fixes a leak
(missing call to mt8186_audsys_clk_unregister()) that would have
happened if any of the syscon_regmap_lookup_by_phandle() calls in
mt8186_init_clock() had failed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: ocelot: call dsa_tag_8021q_unregister() under rtnl_lock() on driver remove
When the tagging protocol in current use is "ocelot-8021q" and we unbind
the driver, we see this splat:
$ echo '0000:00:00.2' > /sys/bus/pci/drivers/fsl_enetc/unbind
mscc_felix 0000:00:00.5 swp0: left promiscuous mode
sja1105 spi2.0: Link is Down
DSA: tree 1 torn down
mscc_felix 0000:00:00.5 swp2: left promiscuous mode
sja1105 spi2.2: Link is Down
DSA: tree 3 torn down
fsl_enetc 0000:00:00.2 eno2: left promiscuous mode
mscc_felix 0000:00:00.5: Link is Down
------------[ cut here ]------------
RTNL: assertion failed at net/dsa/tag_8021q.c (409)
WARNING: CPU: 1 PID: 329 at net/dsa/tag_8021q.c:409 dsa_tag_8021q_unregister+0x12c/0x1a0
Modules linked in:
CPU: 1 PID: 329 Comm: bash Not tainted 6.5.0-rc3+ #771
pc : dsa_tag_8021q_unregister+0x12c/0x1a0
lr : dsa_tag_8021q_unregister+0x12c/0x1a0
Call trace:
dsa_tag_8021q_unregister+0x12c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
RTNL: assertion failed at net/8021q/vlan_core.c (376)
WARNING: CPU: 1 PID: 329 at net/8021q/vlan_core.c:376 vlan_vid_del+0x1b8/0x1f0
CPU: 1 PID: 329 Comm: bash Tainted: G W 6.5.0-rc3+ #771
pc : vlan_vid_del+0x1b8/0x1f0
lr : vlan_vid_del+0x1b8/0x1f0
dsa_tag_8021q_unregister+0x8c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
DSA: tree 0 torn down
This was somewhat not so easy to spot, because "ocelot-8021q" is not the
default tagging protocol, and thus, not everyone who tests the unbinding
path may have switched to it beforehand. The default
felix_tag_npi_teardown() does not require rtnl_lock() to be held. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/idle: mark arch_cpu_idle() noinstr
linux-next commit ("cpuidle: tracing: Warn about !rcu_is_watching()")
adds a new warning which hits on s390's arch_cpu_idle() function:
RCU not on for: arch_cpu_idle+0x0/0x28
WARNING: CPU: 2 PID: 0 at include/linux/trace_recursion.h:162 arch_ftrace_ops_list_func+0x24c/0x258
Modules linked in:
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 6.2.0-rc6-next-20230202 #4
Hardware name: IBM 8561 T01 703 (z/VM 7.3.0)
Krnl PSW : 0404d00180000000 00000000002b55c0 (arch_ftrace_ops_list_func+0x250/0x258)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3
Krnl GPRS: c0000000ffffbfff 0000000080000002 0000000000000026 0000000000000000
0000037ffffe3a28 0000037ffffe3a20 0000000000000000 0000000000000000
0000000000000000 0000000000f4acf6 00000000001044f0 0000037ffffe3cb0
0000000000000000 0000000000000000 00000000002b55bc 0000037ffffe3bb8
Krnl Code: 00000000002b55b0: c02000840051 larl %r2,0000000001335652
00000000002b55b6: c0e5fff512d1 brasl %r14,0000000000157b58
#00000000002b55bc: af000000 mc 0,0
>00000000002b55c0: a7f4ffe7 brc 15,00000000002b558e
00000000002b55c4: 0707 bcr 0,%r7
00000000002b55c6: 0707 bcr 0,%r7
00000000002b55c8: eb6ff0480024 stmg %r6,%r15,72(%r15)
00000000002b55ce: b90400ef lgr %r14,%r15
Call Trace:
[<00000000002b55c0>] arch_ftrace_ops_list_func+0x250/0x258
([<00000000002b55bc>] arch_ftrace_ops_list_func+0x24c/0x258)
[<0000000000f5f0fc>] ftrace_common+0x1c/0x20
[<00000000001044f6>] arch_cpu_idle+0x6/0x28
[<0000000000f4acf6>] default_idle_call+0x76/0x128
[<00000000001cc374>] do_idle+0xf4/0x1b0
[<00000000001cc6ce>] cpu_startup_entry+0x36/0x40
[<0000000000119d00>] smp_start_secondary+0x140/0x150
[<0000000000f5d2ae>] restart_int_handler+0x6e/0x90
Mark arch_cpu_idle() noinstr like all other architectures with
CONFIG_ARCH_WANTS_NO_INSTR (should) have it to fix this. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: soc-compress: Reposition and add pcm_mutex
If panic_on_warn is set and compress stream(DPCM) is started,
then kernel panic occurred because card->pcm_mutex isn't held appropriately.
In the following functions, warning were issued at this line
"snd_soc_dpcm_mutex_assert_held".
static int dpcm_be_connect(struct snd_soc_pcm_runtime *fe,
struct snd_soc_pcm_runtime *be, int stream)
{
...
snd_soc_dpcm_mutex_assert_held(fe);
...
}
void dpcm_be_disconnect(struct snd_soc_pcm_runtime *fe, int stream)
{
...
snd_soc_dpcm_mutex_assert_held(fe);
...
}
void snd_soc_runtime_action(struct snd_soc_pcm_runtime *rtd,
int stream, int action)
{
...
snd_soc_dpcm_mutex_assert_held(rtd);
...
}
int dpcm_dapm_stream_event(struct snd_soc_pcm_runtime *fe, int dir,
int event)
{
...
snd_soc_dpcm_mutex_assert_held(fe);
...
}
These functions are called by soc_compr_set_params_fe, soc_compr_open_fe
and soc_compr_free_fe
without pcm_mutex locking. And this is call stack.
[ 414.527841][ T2179] pc : dpcm_process_paths+0x5a4/0x750
[ 414.527848][ T2179] lr : dpcm_process_paths+0x37c/0x750
[ 414.527945][ T2179] Call trace:
[ 414.527949][ T2179] dpcm_process_paths+0x5a4/0x750
[ 414.527955][ T2179] soc_compr_open_fe+0xb0/0x2cc
[ 414.527972][ T2179] snd_compr_open+0x180/0x248
[ 414.527981][ T2179] snd_open+0x15c/0x194
[ 414.528003][ T2179] chrdev_open+0x1b0/0x220
[ 414.528023][ T2179] do_dentry_open+0x30c/0x594
[ 414.528045][ T2179] vfs_open+0x34/0x44
[ 414.528053][ T2179] path_openat+0x914/0xb08
[ 414.528062][ T2179] do_filp_open+0xc0/0x170
[ 414.528068][ T2179] do_sys_openat2+0x94/0x18c
[ 414.528076][ T2179] __arm64_sys_openat+0x78/0xa4
[ 414.528084][ T2179] invoke_syscall+0x48/0x10c
[ 414.528094][ T2179] el0_svc_common+0xbc/0x104
[ 414.528099][ T2179] do_el0_svc+0x34/0xd8
[ 414.528103][ T2179] el0_svc+0x34/0xc4
[ 414.528125][ T2179] el0t_64_sync_handler+0x8c/0xfc
[ 414.528133][ T2179] el0t_64_sync+0x1a0/0x1a4
[ 414.528142][ T2179] Kernel panic - not syncing: panic_on_warn set ...
So, I reposition and add pcm_mutex to resolve lockdep error. |
| In the Linux kernel, the following vulnerability has been resolved:
bcache: fixup btree_cache_wait list damage
We get a kernel crash about "list_add corruption. next->prev should be
prev (ffff9c801bc01210), but was ffff9c77b688237c.
(next=ffffae586d8afe68)."
crash> struct list_head 0xffff9c801bc01210
struct list_head {
next = 0xffffae586d8afe68,
prev = 0xffffae586d8afe68
}
crash> struct list_head 0xffff9c77b688237c
struct list_head {
next = 0x0,
prev = 0x0
}
crash> struct list_head 0xffffae586d8afe68
struct list_head struct: invalid kernel virtual address: ffffae586d8afe68 type: "gdb_readmem_callback"
Cannot access memory at address 0xffffae586d8afe68
[230469.019492] Call Trace:
[230469.032041] prepare_to_wait+0x8a/0xb0
[230469.044363] ? bch_btree_keys_free+0x6c/0xc0 [escache]
[230469.056533] mca_cannibalize_lock+0x72/0x90 [escache]
[230469.068788] mca_alloc+0x2ae/0x450 [escache]
[230469.080790] bch_btree_node_get+0x136/0x2d0 [escache]
[230469.092681] bch_btree_check_thread+0x1e1/0x260 [escache]
[230469.104382] ? finish_wait+0x80/0x80
[230469.115884] ? bch_btree_check_recurse+0x1a0/0x1a0 [escache]
[230469.127259] kthread+0x112/0x130
[230469.138448] ? kthread_flush_work_fn+0x10/0x10
[230469.149477] ret_from_fork+0x35/0x40
bch_btree_check_thread() and bch_dirty_init_thread() may call
mca_cannibalize() to cannibalize other cached btree nodes. Only one thread
can do it at a time, so the op of other threads will be added to the
btree_cache_wait list.
We must call finish_wait() to remove op from btree_cache_wait before free
it's memory address. Otherwise, the list will be damaged. Also should call
bch_cannibalize_unlock() to release the btree_cache_alloc_lock and wake_up
other waiters. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid0, raid10: Don't set discard sectors for request queue
It should use disk_stack_limits to get a proper max_discard_sectors
rather than setting a value by stack drivers.
And there is a bug. If all member disks are rotational devices,
raid0/raid10 set max_discard_sectors. So the member devices are
not ssd/nvme, but raid0/raid10 export the wrong value. It reports
warning messages in function __blkdev_issue_discard when mkfs.xfs
like this:
[ 4616.022599] ------------[ cut here ]------------
[ 4616.027779] WARNING: CPU: 4 PID: 99634 at block/blk-lib.c:50 __blkdev_issue_discard+0x16a/0x1a0
[ 4616.140663] RIP: 0010:__blkdev_issue_discard+0x16a/0x1a0
[ 4616.146601] Code: 24 4c 89 20 31 c0 e9 fe fe ff ff c1 e8 09 8d 48 ff 4c 89 f0 4c 09 e8 48 85 c1 0f 84 55 ff ff ff b8 ea ff ff ff e9 df fe ff ff <0f> 0b 48 8d 74 24 08 e8 ea d6 00 00 48 c7 c6 20 1e 89 ab 48 c7 c7
[ 4616.167567] RSP: 0018:ffffaab88cbffca8 EFLAGS: 00010246
[ 4616.173406] RAX: ffff9ba1f9e44678 RBX: 0000000000000000 RCX: ffff9ba1c9792080
[ 4616.181376] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9ba1c9792080
[ 4616.189345] RBP: 0000000000000cc0 R08: ffffaab88cbffd10 R09: 0000000000000000
[ 4616.197317] R10: 0000000000000012 R11: 0000000000000000 R12: 0000000000000000
[ 4616.205288] R13: 0000000000400000 R14: 0000000000000cc0 R15: ffff9ba1c9792080
[ 4616.213259] FS: 00007f9a5534e980(0000) GS:ffff9ba1b7c80000(0000) knlGS:0000000000000000
[ 4616.222298] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 4616.228719] CR2: 000055a390a4c518 CR3: 0000000123e40006 CR4: 00000000001706e0
[ 4616.236689] Call Trace:
[ 4616.239428] blkdev_issue_discard+0x52/0xb0
[ 4616.244108] blkdev_common_ioctl+0x43c/0xa00
[ 4616.248883] blkdev_ioctl+0x116/0x280
[ 4616.252977] __x64_sys_ioctl+0x8a/0xc0
[ 4616.257163] do_syscall_64+0x5c/0x90
[ 4616.261164] ? handle_mm_fault+0xc5/0x2a0
[ 4616.265652] ? do_user_addr_fault+0x1d8/0x690
[ 4616.270527] ? do_syscall_64+0x69/0x90
[ 4616.274717] ? exc_page_fault+0x62/0x150
[ 4616.279097] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 4616.284748] RIP: 0033:0x7f9a55398c6b |
