| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: free RNR data on MBSSID mismatch
nl80211_parse_beacon() rejects EMA RNR data when there are fewer RNR
entries than MBSSID entries.
The rejected RNR allocation has not been attached to the beacon data yet,
so free it before returning the error. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: validate PMSR FTM preamble range
PMSR FTM request parsing accepts preamble values outside the
enumerated nl80211 preamble range.
Reject out-of-range values before using them in the parser capability
bit test using the policy.
[drop unnecessary check] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: free AP_VLAN bc_buf SKBs outside IRQ lock
ieee80211_do_stop() removes AP_VLAN packets from the parent AP
ps->bc_buf while holding ps->bc_buf.lock with IRQs disabled. It then
calls ieee80211_free_txskb() before dropping the lock.
ieee80211_free_txskb() is not just a passive SKB release. For SKBs with
TX status state it can report a dropped frame through cfg80211/nl80211,
and that path can reach netlink tap transmit. This is the same reason
the pending queue cleanup in ieee80211_do_stop() already unlinks SKBs
under the queue lock and frees them after IRQ state is restored.
The buggy scenario involves two paths, with each column showing the
order within that path:
AP_VLAN management TX: AP_VLAN stop:
1. attach ACK-status state 1. clear the running state
2. queue a multicast SKB on 2. take ps->bc_buf.lock with IRQs
parent ps->bc_buf disabled
3. unlink the AP_VLAN SKB
4. call ieee80211_free_txskb()
Unlink matching AP_VLAN SKBs from ps->bc_buf under the existing lock,
but move them to a local free queue. Drop the lock and restore IRQ state
before calling ieee80211_free_txskb().
WARNING: kernel/softirq.c:430 at __local_bh_enable_ip |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: initialize SDIO data work before cleanup
brcmf_sdio_probe() stores the newly allocated bus in sdiodev->bus before
allocating the ordered workqueue. If that allocation fails, the function
jumps to fail and calls brcmf_sdio_remove().
brcmf_sdio_remove() unconditionally cancels bus->datawork. Initialize the
work item before the first failure path that can reach brcmf_sdio_remove(),
so the cleanup path always observes a valid work object.
This issue was found by our static analysis tool and then confirmed by
manual review of the probe error path and the remove-time work drain. The
problem pattern is an early setup failure that reaches a cleanup helper
which cancels an embedded work item before its initializer has run.
A QEMU PoC forced alloc_ordered_workqueue() to fail at the same point in
brcmf_sdio_probe(), before INIT_WORK(&bus->datawork) is reached. The
resulting fail path calls brcmf_sdio_remove(), and DEBUG_OBJECTS reports
the invalid work drain with brcmf_sdio_probe() and brcmf_sdio_remove() in
the stack. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: sata_dwc_460ex: enable SATA interrupts only after IRQ handler is registered
sata_dwc_enable_interrupts() is called before platform_get_irq() and
ata_host_activate(), leaving the SATA controller's interrupt mask
enabled without a registered handler. If a later step fails (irq
request, phy init, etc.) or if the controller asserts an interrupt
during probe, the irq line may fire with no handler, causing a
spurious interrupt storm.
Move sata_dwc_enable_interrupts() after ata_host_activate() so that
interrupts are only unmasked once the handler is registered and the
core is fully initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Reject unhashed UDP sockets on sockmap update
UDP sockets get SOCK_RCU_FREE set when (auto-)bound. This means
sk_is_refcounted(unbound) = true, while sk_is_refcounted(bound) = false.
Because sockmap accepts unbound UDP sockets, a BPF program can increment a
socket's refcount via lookup. If the socket is subsequently bound, the
transition from unbound to bound causes bpf_sk_release() to skip the
decrement of the refcount, causing a memory leak.
unreferenced object 0xffff88810bc2eb40 (size 1984):
comm "test_progs", pid 2451, jiffies 4295320596
hex dump (first 32 bytes):
7f 00 00 01 7f 00 00 01 d2 04 1b b7 04 d2 00 00 ................
02 00 01 40 00 00 00 00 00 00 00 00 00 00 00 00 ...@............
backtrace (crc bdee079d):
kmem_cache_alloc_noprof+0x557/0x660
sk_prot_alloc+0x69/0x240
sk_alloc+0x30/0x460
inet_create+0x2ce/0xf80
__sock_create+0x25b/0x5c0
__sys_socket+0x119/0x1d0
__x64_sys_socket+0x72/0xd0
do_syscall_64+0xa1/0x5f0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Instead of special-casing for refcounted sockets, reject unhashed UDP
sockets during sockmap updates, as there is no benefit to supporting those.
This effectively reverts the commit under Fixes, with two exceptions:
1. sock_map_sk_state_allowed() maintains a fall-through `return true`.
2. In the spirit of commit b8b8315e39ff ("bpf, sockmap: Remove unhash
handler for BPF sockmap usage"), the proto::unhash BPF handler is not
reintroduced.
Historical note: this issue is related to commit 67312adc96b5 ("bpf: reject
unhashed sockets in bpf_sk_assign"). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: dummy_hcd: prevent fifo_req reuse during giveback
dummy_hcd embeds a single shared usb_request (dum->fifo_req) that the
"emulated single-request FIFO" fast-path in dummy_queue() reuses for
small IN transfers: it copies the caller's request into it
(req->req = *_req) and queues it, treating list_empty(&fifo_req.queue)
as "the slot is free".
The completion side (dummy_timer/transfer/nuke/dummy_dequeue) follows
the standard pattern: list_del_init(&req->queue) unlinks the request,
then the lock is dropped and usb_gadget_giveback_request() invokes
req->complete(). But list_del_init() makes fifo_req.queue look empty
*before* the completion callback returns, so a concurrent dummy_queue()
on another CPU sees the slot as free, reuses fifo_req and runs
req->req = *_req -- overwriting req->complete while dummy_timer is
mid-calling it. The indirect call then jumps to a clobbered pointer,
causing a general protection fault / page fault in dummy_timer
(syzkaller extid faf3a6cf579fc65591ca). The clobbering write is an
in-bounds memcpy on a live shared object, so KASAN cannot flag it.
Add a fifo_req_busy bit covering the shared request's whole lifetime:
set it in dummy_queue() when the FIFO fast-path takes fifo_req (making
it the fast-path guard, replacing the list_empty(&fifo_req.queue)
test), and clear it after the completion callback has returned, via a
dummy_giveback() helper used at all four gadget-request giveback
sites. The shared slot can no longer be reused until its completion
callback has finished. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: printer: fix infinite loop in printer_read()
printer_read() uses the same variable for the requested copy size and
the number of bytes actually copied to user space. copy_to_user()
returns the number of bytes not copied, so when it fails to copy
anything, the computed copied length becomes zero.
In that case len, buf, current_rx_bytes and current_rx_buf are left
unchanged. If RX data is available and the user buffer remains
unwritable, the read loop can repeat indefinitely.
Track the copied length separately and return -EFAULT, or the number of
bytes already copied, if an iteration makes no progress. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_ncm: validate datagram bounds in ncm_unwrap_ntb()
When unpacking host-supplied NTBs, ncm_unwrap_ntb() checks datagram length
against frame_max but does not verify that the datagram fits within the
declared block length. Additionally, when decoding multiple NTBs from a
single socket buffer, subsequent block lengths are not checked against the
actual remaining buffer data.
With these checks missing, a malicious USB host can specify datagram
offsets and lengths that point beyond the block, or supply secondary NTB
headers declaring lengths larger than the buffer. skb_put_data() then
copies adjacent kernel memory from skb_shared_info into the network skb.
Fix this by verifying that sufficient buffer space remains for the NTB
header before parsing, handling zero-length block declarations, ensuring
that block lengths never exceed the remaining buffer space, and verifying
that each datagram payload stays strictly within the block boundary. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: uvc: clamp SEND_RESPONSE length to the response buffer
uvc_send_response() builds the UVC control response from a user-supplied
struct uvc_request_data:
req->length = min_t(unsigned int, uvc->event_length, data->length);
...
memcpy(req->buf, data->data, req->length);
req->length is clamped to uvc->event_length, which is taken from the
host control request wLength (up to UVC_MAX_REQUEST_SIZE, 64), and to
data->length, which comes from the UVCIOC_SEND_RESPONSE ioctl and is
only checked for being negative. The source buffer data->data is only
60 bytes, so a response with uvc->event_length and data->length both
greater than 60 makes memcpy() read past the end of data->data.
Clamp req->length to sizeof(data->data) as well. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: io_edgeport: cap received transmit credits
The interrupt-status packet reports transmit credits returned by the
device. edge_interrupt_callback() adds the 16-bit value to txCredits
without checking maxTxCredits.
edge_write() uses txCredits minus the software FIFO count as the amount
of data that fits. Since the FIFO is allocated with maxTxCredits bytes,
txCredits exceeding maxTxCredits can cause OOB write in ring buffer.
Cap accumulated credits at maxTxCredits. Conforming devices should never
hit the cap. |
| An elevation of privilege vulnerability exists when the Windows State Repository Service improperly handles objects in memory. An attacker who successfully exploited this vulnerability could run arbitrary code in an elevated context.
An attacker could exploit this vulnerability by running a specially crafted application on the victim system.
The update addresses the vulnerability by correcting the way the Windows State Repository Service handles objects in memory. |
| An elevation of privilege vulnerability exists when the Windows State Repository Service improperly handles objects in memory. An attacker who successfully exploited this vulnerability could run arbitrary code in an elevated context.
An attacker could exploit this vulnerability by running a specially crafted application on the victim system.
The update addresses the vulnerability by correcting the way the Windows State Repository Service handles objects in memory. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: hif_usb: don't dereference hif_dev after re-arming firmware request
ath9k_hif_request_firmware() re-arms an asynchronous firmware load via
request_firmware_nowait(), passing hif_dev as the completion context, and
then still dereferences hif_dev:
dev_info(&hif_dev->udev->dev, "ath9k_htc: Firmware %s requested\n",
hif_dev->fw_name);
The re-armed callback ath9k_hif_usb_firmware_cb() runs on the "events"
workqueue and, when the firmware is missing, walks the retry chain into
ath9k_hif_usb_firmware_fail() -> complete_all(&hif_dev->fw_done). That
releases the wait_for_completion(&hif_dev->fw_done) in a concurrent
ath9k_hif_usb_disconnect(), which then kfree()s hif_dev. The trailing
dev_info() in the frame that re-armed the request can therefore read freed
memory (hif_dev->udev, the first field of struct hif_device_usb):
BUG: KASAN: slab-use-after-free in ath9k_hif_request_firmware
Read of size 8 ... by task kworker/...
ath9k_hif_request_firmware
ath9k_hif_usb_firmware_cb drivers/net/wireless/ath/ath9k/hif_usb.c:1247
request_firmware_work_func
Allocated by ...:
ath9k_hif_usb_probe drivers/net/wireless/ath/ath9k/hif_usb.c
Freed by ...:
ath9k_hif_usb_disconnect -> kfree drivers/net/wireless/ath/ath9k/hif_usb.c
The fw_done barrier only makes disconnect wait for the firmware chain to
*terminate*; it does not protect the outer ath9k_hif_request_firmware()
frame that re-armed the request and keeps touching hif_dev afterwards.
Drop the post-request dev_info(): it is the only use of hif_dev after the
async request is armed, and it is purely informational (the dev_err() on the
failure path runs only when request_firmware_nowait() did not arm a callback,
so hif_dev is still alive there).
This was first reported by syzbot as a single, non-reproduced crash that was
later auto-obsoleted, and was independently rediscovered by the reFuzz fuzzer,
which produced a C reproducer (USB-gadget connect/disconnect of an ath9k_htc
device whose firmware download fails). The vulnerable code is unchanged and
still present in v7.1-rc6, where the slab-use-after-free reproduces under KASAN
once the (sub-microsecond) race window is widened. |
| An elevation of privilege vulnerability exists when the Windows State Repository Service improperly handles objects in memory. An attacker who successfully exploited this vulnerability could run arbitrary code in an elevated context.
An attacker could exploit this vulnerability by running a specially crafted application on the victim system.
The update addresses the vulnerability by correcting the way the Windows State Repository Service handles objects in memory. |
| An elevation of privilege vulnerability exists when the Windows State Repository Service improperly handles objects in memory. An attacker who successfully exploited this vulnerability could run arbitrary code in an elevated context.
An attacker could exploit this vulnerability by running a specially crafted application on the victim system.
The update addresses the vulnerability by correcting the way the Windows State Repository Service handles objects in memory. |
| An elevation of privilege vulnerability exists when the Windows State Repository Service improperly handles objects in memory. An attacker who successfully exploited this vulnerability could run arbitrary code in an elevated context.
An attacker could exploit this vulnerability by running a specially crafted application on the victim system.
The update addresses the vulnerability by correcting the way the Windows State Repository Service handles objects in memory. |
| A remote code execution vulnerability exists when the Windows Jet Database Engine improperly handles objects in memory. An attacker who successfully exploited this vulnerability could execute arbitrary code on a victim system.
An attacker could exploit this vulnerability by enticing a victim to open a specially crafted file.
The update addresses the vulnerability by correcting the way the Windows Jet Database Engine handles objects in memory. |
| A remote code execution vulnerability exists when the Windows Jet Database Engine improperly handles objects in memory. An attacker who successfully exploited this vulnerability could execute arbitrary code on a victim system.
An attacker could exploit this vulnerability by enticing a victim to open a specially crafted file.
The update addresses the vulnerability by correcting the way the Windows Jet Database Engine handles objects in memory. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix NULL pointer dereference in ath11k_hal_srng_access_begin
In ATH11K_QMI_EVENT_FW_READY, ATH11K_FLAG_REGISTERED is set
unconditionally even when ath11k_core_qmi_firmware_ready() fails.
This leaves the driver in an inconsistent state where
initialization is considered complete although the firmware ready
handling did not finish successfully. During the subsequent SSR,
the driver enters the restart path based on this incorrect state
and dereferences uninitialized srng members, resulting in a NULL
pointer dereference.
Call trace:
ath11k_hal_srng_access_begin+0xc/0x60 [ath11k] (P)
ath11k_ce_cleanup_pipes+0x17c/0x180 [ath11k]
ath11k_core_restart+0x40/0x168 [ath11k]
Fix this by:
- skipping firmware_ready if ATH11K_FLAG_REGISTERED is already set
- setting ATH11K_FLAG_REGISTERED only when firmware_ready succeeds
- setting ATH11K_FLAG_QMI_FAIL and aborting the FW_READY handling
on error
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.2.0.c2-00204-QCAMSLSWPLZ-1 |
